Trigger pull on Rem 783

[ifilef]

Hello-

Just purchased Rem 783 in .308.

Intend to presently use it solely for target shooting. Limited to 100 yards but intend to go out to Pala and shoot there at further distances.

The 783 has the adjustable 'Crossfire' trigger.

The factory stock has a molded swivel stud that will not accept a bipod, so firearm will be shot from a bench with sand bags or in a rest of some kind.

Is there a general rule of thumb or customary trigger pull weight that is considered best for accuracy?

I've already adjusted the pull to a certain weight that is quite low and just wondering if it may be too low (or high) for purposes of accurate shot groups, or not.

[ChuckDizzle]

Generally lighter, shorter, crisper means more accuracy, but most people will experience diminished returns eventually. A good trigger can vary from person to person.

3lbs seems to be a sweet spot for most.

[FourT6and2]

I've got my trigger set to 1.5 lbs. But it's all personal preference really. At first 1.5 seemed really light. But now it's quite normal. In fact, I could see myself going down to 1 lb.

For your rig, though, you probably won't see any significant gains. You'd be well off shooting prone, from a pack. just put the rifle on a backpack or sand bag. No need for a rest.

[SMarquez]

As long as it passes the bump test you can go as light as you are comfy with. For range only shooting go as low as you feel safe with. For hunting and jostling around I like 3.5-4 lbs. Mine was 3.5 out of the box. I give mine a pretty good bump with a rubber mallet and a good smack on the ground. I was able to get a cheapie Caldwell bipod on mine.

[ifilef]

I've got my trigger set to 1.5 lbs. But it's all personal preference really. At first 1.5 seemed really light. But now it's quite normal. In fact, I could see myself going down to 1 lb.

For your rig, though, you probably won't see any significant gains. You'd be well off shooting prone, from a pack. just put the rifle on a backpack or sand bag. No need for a rest.

As long as it passes the bump test you can go as light as you are comfy with. For range only shooting go as low as you feel safe with. For hunting and jostling around I like 3.5-4 lbs. Mine was 3.5 out of the box. I give mine a pretty good bump with a rubber mallet and a good smack on the ground. I was able to get a cheapie Caldwell bipod on mine.

FourT- Well, I've got mine down to 1 lb. 11 oz. It does seem light, but I do understand the comment that yours now seems 'normal' to you.

However, I'm now thinking of increasing it to 2.5 lbs. because that's the minimum trigger pull I can get out of the Accutrigger in my Savage Axis II in .223- and thinking that consistency between those two triggers might be better overall. Thoughts? Comments? Your 'thoughts' is too 'femme' a question. Sorry about that...

SMarquez- The trigger on the 783 contains a 'trigger release' in front of it that if not depressed first the trigger will not be activated. I don't understand nor have I ever done a 'bump' test. Assuming the safety is 'OFF' with this particular trigger wouldn't it be all but impossible for gun to discharge because it's similar in a sense to a Glock trigger but even more so to Savage's Accutrigger?

In any event, I will perform the trigger tests and use a punch on the sear as recommended in the detailed manual instructions and may try the bump test you have described.

Which Caldwell bipod? It's really difficult to find ANY bipod that works on the 783 molded swivel stud. I called Remington and they said none were compatible- need to get a different stock. I've already had to return a nice decently priced UTG bipod to Amazon for that reason.

[Horrendo Revolver]

I sell firearms at Cabela's and have seen numerous instances where people mounted bipods on rifles with molded in plastic swivel studs. They broke the stud so then even a sling couldn't be mounted.

[ifilef]

I sell firearms at Cabela's and have seen numerous instances where people mounted bipods on rifles with molded in plastic swivel studs. They broke the stud so then even a sling couldn't be mounted.

Good to know! Thanks for your post.

[SMarquez]

FourT- Well, I've got mine down to 1 lb. 11 oz. It does seem light, but I do understand the comment that yours now seems 'normal' to you.

However, I'm now thinking of increasing it to 2.5 lbs. because that's the minimum trigger pull I can get out of the Accutrigger in my Savage Axis II in .223- and thinking that consistency between those two triggers might be better overall. Thoughts? Comments? Your 'thoughts' is too 'femme' a question. Sorry about that...

SMarquez- The trigger on the 783 contains a 'trigger release' in front of it that if not depressed first the trigger will not be activated. I don't understand nor have I ever done a 'bump' test. Assuming the safety is 'OFF' with this particular trigger wouldn't it be all but impossible for gun to discharge because it's similar in a sense to a Glock trigger but even more so to Savage's Accutrigger?

In any event, I will perform the trigger tests and use a punch on the sear as recommended in the detailed manual instructions and may try the bump test you have described.

Which Caldwell bipod? It's really difficult to find ANY bipod that works on the 783 molded swivel stud. I called Remington and they said none were compatible- need to get a different stock. I've already had to return a nice decently priced UTG bipod to Amazon for that reason.

When a trigger is adjusted the gun should be bumped to simulate accidentally dropping or simulating a jolt that would disturb the sear. I have done this with Timneys, older Remingtons and Winchester. They are all different. I have not messed with the trigger on the 783 so I am not real familiar with it.
Here are some pics. I will tell you it is not a great bipod, it works loose so you got to stay on it.
mounted

Part Number?

When or if mjne breaks I'll go with one of these. Randall at AR15barrels.com approves.

https://www.boydsgunstocks.com/ProductDetail/3ua124d1g203_pro-varmint--centerfire-remington-783-short-action-detachable-box-mag-factory-barrel-channel-natblk-f

[ifilef]

SMarquez- Thanks for the photos and your post, above.

Unfortunately, without more, I can not locate the bipod by punching in the 071012 number. It is apparently not a model number.

If you might have the model name and center height extended it might be of help.

Horrendo- I would assume that even if I were to locate the particular Caldwell you would advise against using it on the Rem 783. Well, I certainly don't want to purchase a Boyd stock later on, so, SMarquez, don't go out of your way to provide the info to me.

Perhaps someone might recommend a compatible sling for the 783 that would attach directly to the swivel stud without need for eyelets or swivels, whatchamacallits.

[ifilef]

For those interested in a new 783, Remington is currently offering a mail-in rebate of $40 on it.

[LynnJr]

Most 100 yard guns shot off of a bench are using very light trigger pull weights so the gun doesn't move when your pulling the trigger.
Jewell Kelbly Bix&Andy Flavio Fare triggers are what you will see on the line.
In the case of the 783 set it as light as it is reliable as has already been posted.
If you need lighter than that look up the 4 brands listed.

[Flouncer]

Bipods.

Caldwell is made in China, Harris is Made in USA. Vote with your pocketbook or your consciences. Then reap the harvest when your turn comes around.

[TMB 1]

Caldwell is made in China, Harris is Made in USA. Vote with your pocketbook or your consciences. Then reap the harvest when your turn comes around.

Does that mean put Caldwell on foreign made rifles like Howa, Tikka etc... and put Harris on USA made rifles like Remington, Savage etc...?