Unconfigured Ad Widget

Collapse

Problems sighting in a gun!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • dirtriderkevin
    Junior Member
    • Feb 2013
    • 23

    Problems sighting in a gun!

    Have a friend with a savage 30-06 he mounted a nikon prostaff on some Leupold rails. Took it out today to sight it in but its shooting way to high. Even with the turret bottomed out can't get it on paper at 100 yards? Any tips?
  • #2
    drmjf
    • Jul 2011
    • 205

    You may need the rails changed to lower the point of impact, could be the scope mount are wrong, need to have a gunsmith check it out for proper alignment.
    sigpic
    Michael J Fernandes owner
    Gecko Guns Gunsmith "Repairs done Right"
    510-914-6396
    Ham radio operator KI6SDO
    NRA Certified Pistol, Rifle and PPOH
    [/url]www.GeckoGuns.com[/url]
    Pinole, CA 94564
    "The nine most terrifying words in the English language are: 'I'm from the government and I'm here to help.'" Ronald Regan

    Comment

    • #3
      JMP
      Internet Warrior
      CGN Contributor - Lifetime
      • Feb 2012
      • 17056

      Assuming everything is done correctly, this is usually caused by a misalignment in your front and rear ring height. Make sure your mounts are fully engaged with the rail. A picture would probably be helpful. If your shots are too high. It's easier to bore sight it while you are at home and play with the knobs. Make sure you are turning them in the right direction.

      Comment

      • #4
        Divernhunter
        Calguns Addict
        • May 2010
        • 8753

        Where are you located. It is hard to have trouble with Leupold mounts.
        A 30cal will reach out and touch them. A 50cal will kick their butt.
        NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
        SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

        Comment

        • #5
          Jeepergeo
          Veteran Member
          • Feb 2012
          • 3507

          Buy a bore sight, center the scope turrets, then bore sight at 25 yards. If you are way off, remove scope and check that rings are in a straight line. Otherwise, adjust to bring into bull at 25 yards, then go to range and shoot to bring in at 100 yds.
          Benefactor Life Member, National Rifle Association
          Life Member, California Rifle and Pistol Association

          Comment

          • #6
            bsumoba
            Veteran Member
            • Sep 2012
            • 4217

            if you have a canted rail like a 20MOA base, then maybe it is installed reversed?
            so now you have a scope that is canted up, rather than down.
            Visit- www.barrelcool.com
            The Original Chamber Flag and Barrel Cooler in 1
            Instagram: barrelcool_

            Comment

            • #7
              Ross
              Senior Member
              • Apr 2009
              • 1285

              Is the scope on backwards?
              sigpicand as a check against tyranny." Judge Benitez - March 2019

              Comment

              • #8
                boomer135
                Senior Member
                • Apr 2012
                • 580

                Did you try removing the turret and adjusting the elevation? you may have reached the locking point with the turret attached.

                Comment

                • #9
                  Thefeeder
                  Calguns Addict
                  • Jun 2007
                  • 5011

                  ><

                  Just because I've seen it done before.....Is the windage knob sitting the right side or left side of the scope

                  Comment

                  • #10
                    RobertMW
                    Senior Member
                    • Jul 2013
                    • 2117

                    Originally posted by bsumoba
                    if you have a canted rail like a 20MOA base, then maybe it is installed reversed?
                    so now you have a scope that is canted up, rather than down.
                    If that were the case, he would be shooting way below. If anything, if it were a canted base, he could have bought something with way too much cant for what his scope can adjust out, but scopes with that little adjustment and rails with that much elevation are few and far between.

                    Originally posted by Thefeeder
                    Just because I've seen it done before.....Is the windage knob sitting the right side or left side of the scope
                    Damn, how did they adjust the elevation? And how tall was the mount to get clearance under it for that?
                    Originally posted by kcbrown
                    I'm most famous for my positive mental attitude.

                    Comment

                    • #11
                      Crazydave
                      Member
                      • Mar 2015
                      • 311

                      I had a similar issue.
                      I wasted like 10 rounds before I figured out that I was WAY off.

                      Your 1st step should be to hit the paper. By bringing the target closer you will a really good idea of where you're pointed. Turns out my scope was set to the extreme "Down" and "Left", which is why I wasn't hitting the target even at 50 yards.

                      Bring your target in closer like 10 or 25 yards and see where it's hitting.
                      Then take it out to 25 yards, and see how you are doing, make some adjustments
                      then to 50 (then some adjustments)
                      then to 75 (then some adjustments)
                      then to 100 and fine tune.
                      Last edited by Crazydave; 08-18-2015, 10:19 AM.

                      Comment

                      • #12
                        RogerOrange
                        Member
                        • Apr 2015
                        • 320

                        When I visited my gunsmith to get my rifle I learned that the base has a high and low side and it should be mounted with the high side towards back so the scope will point downwards.
                        At first I was confused but then realized what by having the scope point down it will raise the barrel to compensate for bullet drop..

                        In short check if you have installed the scope base

                        Comment

                        • #13
                          Calif Hunter
                          Veteran Member
                          • Aug 2003
                          • 3326

                          If it is a two piece base set, are they installed properly - the rear base on the rear receiver and vice versa? Like others have suggested, start at 25 yards or closer and see where the bullet hits.

                          Comment

                          • #14
                            RNE228
                            Senior Member
                            • Oct 2013
                            • 2458

                            First step should be to bore sight. A bolt action is so easy. I've done them in the back yard. Set a target up at far end of yard. Set rifle on sandbags, with bolt out. Adjust sand bags so target is in cent of bore. Adjust scope or sights so they are on target.

                            It's free, and simple. You should be on target at 25 yards using that method. Done this on all the bolt action rifles I have had.

                            Alternative is to buy a laser bore sight.

                            Originally posted by Crazydave
                            I had a similar issue.
                            I wasted like 10 rounds before I figured out that I was WAY off.

                            Your 1st step should be to hit the paper.

                            Comment

                            • #15
                              BIRDHUNTER757
                              Junior Member
                              • Mar 2011
                              • 51

                              Sounds like you might have 20MOA rail and a set of 20MOA rings for a total of 40MOA. Check the specs on the rail and rings. That's where I would start.

                              Comment

                              Working...
                              UA-8071174-1