Installing night sights on USPc 9mm

[LambertHK]

Since this is my first post, I'd first like to say hello to everyone here. I'm planning to get the B&J Machine PI Model 500 tool to install meprolight tru dot sights on my gun. Does anyone have this or had experience using it?

[Gregchico]

Yep, it will work just fine. I installed three sets of night sights on my USPcs using mine.

[l_Z_l]

it's it pretty easy w/ that tool? i migh consider getting that to change my sights out as well.

any one know if that tool good for other guns? sig, xd, 1911, etc

[1911su16b870]

it's it pretty easy w/ that tool? i migh consider getting that to change my sights out as well.

any one know if that tool good for other guns? sig, xd, 1911, etc

I have the Midwest Industries 1911 sight pusher and the Trijicon 1911 front sight staking tool, they work for the 1911 pistol.

[Gregchico]

it's it pretty easy w/ that tool? i migh consider getting that to change my sights out as well.

any one know if that tool good for other guns? sig, xd, 1911, etc

I have used it on my Sigs, but I would not use it with XDs as the XD sights are so tightly on there it can damage the tool.

I have used it on my S&W 1911s, but there are dovetail sights.

[LambertHK]

Thanks, since I plan to purchase a few more handguns I think I'll get my money's worth if I install the sights myself. I searched online and the only place that sells it is Midway. Most of the people that bought it really like it. This tool should work for HK as well as 1911, Glock, and Sig according the the reviews.

[AC Gould]

You might just want to save some money and just get yourself a set of brass punches first. I changed the sights on my USP to Mepro adjustables using only a small punch and small brass hammer. The tools are nice if you run into one that's really stuck or you want to adjust a fixed rear frequently. My $.02

[LambertHK]

You might just want to save some money and just get yourself a set of brass punches first. I changed the sights on my USP to Mepro adjustables using only a small punch and small brass hammer. The tools are nice if you run into one that's really stuck or you want to adjust a fixed rear frequently. My $.02

Yeah this tool is a little pricey and may not be worth it if you're just installing sights for 1-2 pistols. Since I already placed the order, I'll have to make good use out of it.

[l_Z_l]

You might just want to save some money and just get yourself a set of brass punches first. I changed the sights on my USP to Mepro adjustables using only a small punch and small brass hammer. The tools are nice if you run into one that's really stuck or you want to adjust a fixed rear frequently. My $.02

where would you recommend getting a set from?

I'll probably change out sights on my guns as i get more...i have 3 for now...til i start expanding my collection...this also allows me to experiment w/ different sights

[AC Gould]

Brass punches

Try Brownells, Midway, Sportsmans Guide / Cheaper than Dirt - (They sell a cheap Chinese set w/ hammer ) or even check out Harbor Freight. Brownells and Midway have the really good stuff, but the cheap Chinese stuff will do the job for occasional work and are good to keep in your shooting box for range repairs.

[Matt P]

Like AC, I am also in complete agreement on his suggested method.

In fact on Glocks, I would use a Brownells small hammer, one side brass, the other nylon, and just drive out the rear sight with that. (using Nylon end). I have done many, many Glocks this way.
I also would use this method for most other handguns.

Some things to consider..
Be careful on drifting the front sight from the dovetail if one present. See about getting yourself a nylon drift, or such a steel one with replaceable nylon ends. Again Brownells.
Make sure to have yourself a fine file to relieve the new sights dovetail slightly if needed.
Be careful on where you hit the front sight. I damaged a front sight night sight by not being careful enough. Only strike the part that is the bottom dovetail.
Take your time, file off if you know the dovetail will be way too tight.

You can add some red lock tite to the dovetail if you file too much.

I couldnt imagine buying a tool unless I was going to do many sights.

Great suggestion AC.

[aplinker]

+1... I've done a few without a sight pusher. It's not that tough... vise it up and tap them through. I switched to DIY after I glimpsed a top 10 gunsmith (I won't say who) do it this way.

Like AC, I am also in complete agreement on his suggested method.

In fact on Glocks, I would use a Brownells small hammer, one side brass, the other nylon, and just drive out the rear sight with that. (using Nylon end). I have done many, many Glocks this way.
I also would use this method for most other handguns.

Some things to consider..
Be careful on drifting the front sight from the dovetail if one present. See about getting yourself a nylon drift, or such a steel one with replaceable nylon ends. Again Brownells.
Make sure to have yourself a fine file to relieve the new sights dovetail slightly if needed.
Be careful on where you hit the front sight. I damaged a front sight night sight by not being careful enough. Only strike the part that is the bottom dovetail.
Take your time, file off if you know the dovetail will be way too tight.

You can add some red lock tite to the dovetail if you file too much.

I couldnt imagine buying a tool unless I was going to do many sights.

Great suggestion AC.