Unconfigured Ad Widget

Collapse

Glock trigger issue

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 9mm1911
    Member
    • Apr 2013
    • 235

    Glock trigger issue

    Hey all,

    Just cleaning my guns and noticed that the trigger pull on my Gen4 G17 felt like it got noticeably heavier than before.

    Measured it with my trigger pull gauge and it was coming in at 7.5 - 8lbs

    I measured the trigger when I first bought the G17 and while I don't remember what exactly it was, but I know for a fact it never pulled 8lbs.

    I've made no alterations and have never even done anything other than a basic field strip on it.

    Only thing is that I let my nephew shoot it... and that kid literally breaks everything he touches (j/k, but seriously, I've taken him paintballing once a month for years, and he breaks something every single time. I think maybe he's cursed my Glock.)

    Anyone else have this issue?


    Edit/update:
    Detail strip, proper clean/lube, and now it's consistently pulling right between 7 to 7 1/4 lbs.

    Feels more like it did when I first bought it.
    Last edited by 9mm1911; 02-05-2014, 7:01 AM.
    sigpic
  • #2
    Nismo
    Senior Member
    • Apr 2006
    • 569

    Worth a look if you have taken the trigger assembly out recenty but

    make sure the rear trigger spring that connects to the bottom of the trigger bar is lined up on the bottom of the trigger bar.

    There is a little notch right in the middle that is on the bottom where the spring hooks into. Otherwise it will be crooked and rub up against the side of the trigger housing.

    Comment

    • #3
      tbc
      Calguns Addict
      • Jun 2011
      • 5955

      The safety plunger spring may not seat properly.


      Sent via Tapatalk

      Comment

      • #4
        RobertMW
        Senior Member
        • Jul 2013
        • 2117

        Have you ever cleaned it?

        JK, although doing a through strip and clean of the frame and slide could reveal some major deposits that you don't get when you are just doing a basic field strip. If you could describe exactly where in the pull you are feeling it, that would be helpful because of how the different springs and mechanisms engage. If it is through out the entire pull, yes the trigger connector spring hay have gotten out of place, if it is a short area in the middle of the pull, about the first half, then it could be the striker safety, either dirty or damaged, I've also seen small amounts of sheared metal jammed inside of a striker safety, usually just from initial break in, not a long term problem. If it is late in the pull, you may have build-up in the striker itself, the last 1/8" is finishing cocking the striker back and releasing.
        Originally posted by kcbrown
        I'm most famous for my positive mental attitude.

        Comment

        • #5
          Corbin Dallas
          CGN/CGSSA Contributor - Lifetime
          CGN Contributor - Lifetime
          • May 2006
          • 6458

          Did you put oil on the connector and sear?
          NRA Life Member and Certified Instructor: Pistol - Rifle - Shotgun - PPITH - PPOTH - NRA Certified RSO

          WTB the following - in San Diego
          --Steyr M357A1 357SIG
          --Five Seven IOM (round trigger guard)

          Never forget - השואה... לעולם לא עוד.

          Comment

          • #6
            nitrous_bob
            Banned
            • Dec 2012
            • 251

            glocks are hard to do a trigger pull test. because your fighting the "safe action" while trying to get a consistent pull on the gauge

            how many times did you do it ? if you got 6 or so in a row...then its probably accurate

            just get a lone wolf 3.5 lb connector if everything is working properly

            Comment

            • #7
              nahpungnome
              Senior Member
              • Oct 2013
              • 2159

              My G19 pulls 6.5# avg on my Lyman gauge, but it's pretty difficult to get a consistent reading as mentioned above.

              Comment

              • #8
                G-forceJunkie
                Calguns Addict
                • Jul 2010
                • 6530

                Make sure the trigger spring is not broken. That spring actually pulls the trigger bar backwards so if its gone, the trigger pull weight increases. Another symptom of this spring being broken is it will sometimes not reset the trigger if your not holding it to the rear when cycling the slide.

                Comment

                • #9
                  DFence
                  • Feb 2012
                  • 1368

                  Sounds like possible over lubrication and you have fluid in the striker channel causing it to hydraulic up.

                  The trigger on a Glock should never change unless you change something or something is wrong. If it is noticeably different, get it looked at.
                  Its not paranoid.....its prepared.

                  NRA Certified Pistol/Rifle/Shotgun/PPIH/PPOH Instructor | NRA Certified RSO | NRA Life Member | GSSF Life Time Member | Surefire Low Light Instructor | Glock Certified Armorer | Utah CCW Instructor | Nevada CCW Instructor

                  Comment

                  • #10
                    ElDub1950
                    Calguns Addict
                    • Aug 2012
                    • 5688

                    Originally posted by DFence
                    Sounds like possible over lubrication and you have fluid in the striker channel causing it to hydraulic up.
                    .
                    Nephew topped it off with 10W40

                    Comment

                    • #11
                      Bill Steele
                      Calguns Addict
                      • Sep 2010
                      • 5028

                      Originally posted by Corbin Dallas
                      Did you put oil on the connector and sear?
                      Be my guess as well. A drop of oil between the trigger bar and the connector does wonders for keeping them running.

                      A detail strip, complete clean of everything then light lube where the armorer manual calls out and you should be rocking again.
                      When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

                      Comment

                      • #12
                        9mm1911
                        Member
                        • Apr 2013
                        • 235

                        Thanks for all the advice.
                        Detail strip, clean/lube, and now it's consistently pulling right between 7 to 7 1/4 lbs.

                        Feels more like it did when I first bought it. Thanks
                        sigpic

                        Comment

                        • #13
                          DFence
                          • Feb 2012
                          • 1368

                          Originally posted by ElDub1950
                          Nephew topped it off with 10W40

                          Hahahaha!


                          Sent from my iPhone using Tapatalk
                          Its not paranoid.....its prepared.

                          NRA Certified Pistol/Rifle/Shotgun/PPIH/PPOH Instructor | NRA Certified RSO | NRA Life Member | GSSF Life Time Member | Surefire Low Light Instructor | Glock Certified Armorer | Utah CCW Instructor | Nevada CCW Instructor

                          Comment

                          • #14
                            saki302
                            Calguns Addict
                            • Oct 2005
                            • 7193

                            Take it down completely, clean it, lube and reassemble. It's probably just dirty or lubed wrong

                            If he can break a Glock by shooting it, we should make him a trophy.

                            On that thought- why did you let him borrow it?!?!?!

                            -Dave

                            Comment

                            Working...
                            UA-8071174-1