Unconfigured Ad Widget

Collapse

...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Erick Danielsen
    Senior Member
    • Aug 2012
    • 546

    ...

    ...
    Last edited by Erick Danielsen; 09-09-2014, 4:55 PM.
  • #2
    9mmepiphany
    Calguns Addict
    • Jul 2008
    • 8075

    Can we get some clarification on some of your problems?

    What is a "feeder edge"?
    Are the case mouths getting stuck on the front edge of the magazine:
    1. on all the magazines or just one?
    2. during just the first round, the middle rounds. the last rounds?
    3. when being fired?
    4. when being hand fed?
    ...because the journey is the worthier part...The Shepherd's Tale

    Comment

    • #3
      Erick Danielsen
      Senior Member
      • Aug 2012
      • 546

      Originally posted by 9mmepiphany
      Can we get some clarification on some of your problems?

      What is a "feeder edge"?
      Are the case mouths getting stuck on the front edge of the magazine:
      1. on all the magazines or just one?
      2. during just the first round, the middle rounds. the last rounds?
      3. when being fired?
      4. when being hand fed?
      Sorry... yes, the case mouths are getting stuck on the front edge of the magazine.
      1. Yes, on both mags.
      2. Last few rounds
      3. Yes.
      4. Yes.

      Comment

      • #4
        Erick Danielsen
        Senior Member
        • Aug 2012
        • 546

        My "feeder" edge was a typo, meant to type follower...

        Comment

        • #5
          jpm804
          Senior Member
          • Jan 2012
          • 1609

          I swear I read a similar thread here on calguns in the past where someone was having a similar issue... he found a thread on another forum where someone was having the same issue.

          It was related to when he switched his magazine release to lefty.. sorry cant find the post. But you might want to look into that if all else fails...

          Comment

          • #6
            ElDub1950
            Calguns Addict
            • Aug 2012
            • 5688

            These are the reasons you should always give a new gun, especially your first one, several hundred rounds test firing before tinkering with it.

            Comment

            • #7
              Fuel&Fire
              Member
              • Jan 2011
              • 183

              Factory Magazines?

              I have an M&P 9mm Full Size, never had a single issue - shooting reloads, federal, etc. Maybe send back to S&W to check it out...

              Comment

              • #8
                ExtremeX
                Calguns Addict
                • Sep 2010
                • 7160

                Originally posted by ElDub1950
                These are the reasons you should always give a new gun, especially your first one, several hundred rounds test firing before tinkering with it.
                ExtremeX

                Comment

                • #9
                  P5Ret
                  Calguns Addict
                  • Oct 2010
                  • 6406

                  Did you take the mags apart? I have seen a similar issue when someone reassembled a mag with the spring in wrong. It caused the back of the follower to sit slightly higher than the front, and rounds would catch on the front edge of the mag.

                  Comment

                  • #10
                    chonkey
                    Senior Member
                    • Aug 2010
                    • 528

                    Originally posted by jpm804
                    I swear I read a similar thread here on calguns in the past where someone was having a similar issue... he found a thread on another forum where someone was having the same issue.

                    It was related to when he switched his magazine release to lefty.. sorry cant find the post. But you might want to look into that if all else fails...
                    I remember reading it too. I think he said this is a known issue with M&Ps when switched to lefty.

                    Comment

                    • #11
                      Shapes And Colors
                      Member
                      • Jun 2012
                      • 342

                      Originally posted by ElDub1950
                      These are the reasons you should always give a new gun, especially your first one, several hundred rounds test firing before tinkering with it.
                      I'm not sure I would call switching a factory ambidextrous part to lefty "tinkering". The gun is advertised as being ambi, if it does not function that way, there is something wrong.
                      Originally posted by Kestryll
                      And that boys and girls is what stepping on your own dick sounds like.

                      Comment

                      • #12
                        ElDub1950
                        Calguns Addict
                        • Aug 2012
                        • 5688

                        Originally posted by Shapes And Colors
                        I'm not sure I would call switching a factory ambidextrous part to lefty "tinkering". The gun is advertised as being ambi, if it does not function that way, there is something wrong.
                        No dispute there that it should work.

                        My point was that it doesn't work and now it's unknown if it was a problem with the gun right out of the box or if the problem was caused by an error while while swapping the mag release.

                        Comment

                        • #13
                          Shapes And Colors
                          Member
                          • Jun 2012
                          • 342

                          Originally posted by ElDub1950
                          No dispute there that it should work.

                          My point was that it doesn't work and now it's unknown if it was a problem with the gun right out of the box or if the problem was caused by an error while while swapping the mag release.
                          Makes sense, fair enough.
                          Originally posted by Kestryll
                          And that boys and girls is what stepping on your own dick sounds like.

                          Comment

                          • #14
                            stretch64
                            Member
                            • Dec 2007
                            • 173

                            4 M&Ps, 2 full size and 2 Pros, and never had a problem switching the mag release from right to left.
                            Rotate the retaining rod out of its slot in the mag release and make sure it's fully seated in the hole in the frame, then rotate it back into place in the mag release.
                            Load your magazines to capacity and let them sit that way for at least a few days.

                            Comment

                            • #15
                              9mmepiphany
                              Calguns Addict
                              • Jul 2008
                              • 8075

                              Originally posted by Erick Danielsen
                              Sorry... yes, the case mouths are getting stuck on the front edge of the magazine.
                              1. Yes, on both mags.
                              2. Last few rounds
                              3. Yes.
                              4. Yes.
                              If it is just the last few rounds, that means the extractor is working fine with the rounds before them...which leave the mag spring

                              You mention it is your first gun, but not that it is new. I'd also suspect that the magazine spring was assembled backwards...a combo of the weak spring effect and the follower sticking.

                              I'd take them apart and see if turning one around makes a difference.

                              If that isn't it, I'd call S&W CS in the morning
                              ...because the journey is the worthier part...The Shepherd's Tale

                              Comment

                              Working...
                              UA-8071174-1