This response was posted to another member's thread. But since I've received several inquiries and PMs regarding how to function check a Sig DA/SA P220/226/229/239, I thought I'd post it again for those wanting the information.
Sig has several safety features built into the design of their weapon that interact with each other. They include the Decocking Lever, the Safety Intercept Notch, the Trigger Bar Disconnect and the Firing Pin Safety Block. Below is the procedure I, as an armorer, use to test a weapon after every cleaning or service to confirm that these safety features are functioning properly.
Make sure the weapon is unloaded by visually and physically checking the chamber and magwell. Check it once, check it twice, check it a third time. Make sure the weapon is clear. I NEVER clean or work on weapons with ammunition or loaded magazines in the same room.
1. Disassemble the weapon. Clean, inspect, lubricate and reassemble.
2. After reassembly and pivoting the take-down lever horizontally, rack the slide a couple of times.
3. Insert an EMPTY magazine and pull the slide to the rear. The slide should lock back as the magazine follower lifts the Slide Catch Lever, causing it to engage the slide. This tests the Slide Catch Lever and arresting notch on the slide.
4. Press the magazine release button. The magazine should fall freely. Now use the Slide Catch Lever to release the slide to see that it closes with authority. This tests the strength of the recoil spring.
5. Using the Decocking Lever, decock the gun. Using the Decocking Lever disengages the cocked hammer from the sear and allows safe lowering of the hammer to the Safety Intercept Notch. The hammer should fall short and NOT touch the firing pin. Push on the back of the hammer. It should not move and feel very solid. This tests the Decocking Lever and Safety Intercept Notch. ALWAYS USE THE DECOCKING LEVER TO LOWER THE HAMMER. ****DO NOT hold the hammer with your fingers, press the trigger and try to lower the hammer down. This will bypass the safety features and could cause a negligent discharge****
6. Pull the trigger Double Action (DA). The hammer should cock and release, striking the firing pin. The insures the gun operates in DA mode.
7. Pull the trigger and hold it to the rear. Rack the slide while holding the trigger, the slide moves forward into battery while the hammer remains in the fully cocked position...this indicates that the disconnector functions and the gun will only fire once per trigger pull. After racking the slide, let off on the trigger until you hear it click. This indicates the sear has re-engaged the hammer and is reset for Single Action operation (SA). Pull the trigger and the hammer will fall, striking the firing pin. This insures the gun operates in SA mode.
8. Lastly, grab the slide and pull it to the rear about 1/4" or so and pull the trigger. The trigger should travel to the rear without engagement or resistance of any kind. This insures the Trigger Bar Disconnect is functioning properly.
After performing the above function tests, your gun should be good to go. Any failure of one or more of the above and the gun should be inspected by Sig or a qualified armorer.
Hope this helps keep your Sigs running smoothly...Sig Marine (Certified Sig Armorer)
Sig has several safety features built into the design of their weapon that interact with each other. They include the Decocking Lever, the Safety Intercept Notch, the Trigger Bar Disconnect and the Firing Pin Safety Block. Below is the procedure I, as an armorer, use to test a weapon after every cleaning or service to confirm that these safety features are functioning properly.
Make sure the weapon is unloaded by visually and physically checking the chamber and magwell. Check it once, check it twice, check it a third time. Make sure the weapon is clear. I NEVER clean or work on weapons with ammunition or loaded magazines in the same room.
1. Disassemble the weapon. Clean, inspect, lubricate and reassemble.
2. After reassembly and pivoting the take-down lever horizontally, rack the slide a couple of times.
3. Insert an EMPTY magazine and pull the slide to the rear. The slide should lock back as the magazine follower lifts the Slide Catch Lever, causing it to engage the slide. This tests the Slide Catch Lever and arresting notch on the slide.
4. Press the magazine release button. The magazine should fall freely. Now use the Slide Catch Lever to release the slide to see that it closes with authority. This tests the strength of the recoil spring.
5. Using the Decocking Lever, decock the gun. Using the Decocking Lever disengages the cocked hammer from the sear and allows safe lowering of the hammer to the Safety Intercept Notch. The hammer should fall short and NOT touch the firing pin. Push on the back of the hammer. It should not move and feel very solid. This tests the Decocking Lever and Safety Intercept Notch. ALWAYS USE THE DECOCKING LEVER TO LOWER THE HAMMER. ****DO NOT hold the hammer with your fingers, press the trigger and try to lower the hammer down. This will bypass the safety features and could cause a negligent discharge****
6. Pull the trigger Double Action (DA). The hammer should cock and release, striking the firing pin. The insures the gun operates in DA mode.
7. Pull the trigger and hold it to the rear. Rack the slide while holding the trigger, the slide moves forward into battery while the hammer remains in the fully cocked position...this indicates that the disconnector functions and the gun will only fire once per trigger pull. After racking the slide, let off on the trigger until you hear it click. This indicates the sear has re-engaged the hammer and is reset for Single Action operation (SA). Pull the trigger and the hammer will fall, striking the firing pin. This insures the gun operates in SA mode.
8. Lastly, grab the slide and pull it to the rear about 1/4" or so and pull the trigger. The trigger should travel to the rear without engagement or resistance of any kind. This insures the Trigger Bar Disconnect is functioning properly.
After performing the above function tests, your gun should be good to go. Any failure of one or more of the above and the gun should be inspected by Sig or a qualified armorer.
Hope this helps keep your Sigs running smoothly...Sig Marine (Certified Sig Armorer)




Comment