Unconfigured Ad Widget

Collapse

S&W 625 PC problems. NEED HELP!!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sammy
    Veteran Member
    • Oct 2006
    • 3847

    S&W 625 PC problems. NEED HELP!!

    I am at my wits end. The first thing I did was post over at the S&W forum and I am not getting any results.

    A quick recap, day 1, NIB 625 Performance Center shoots 100%. Very great gun, lots of fun. Could not be happier. Shooting my 230g. Zero's using Winchester primers nd 200g. LSWC using Wolf primers.

    Day 2 light strikes galore. Found the strain screw backed out so it was tightened up which helped a bit but still 1-2 light strikes per cylinder. I got a box of factory and had the same results.

    Day 3 after installing a Cylinder & Slide firing pin it ran 100% with the exception of the firing pin getting lodged in the Wolf primer locking up the gun. No good.

    Day 4 I installed an Apex pin and spring and it was no better than the factory pin. This one might have been worse. Light strikes on nearly half of the primers strikes. This was using a combo of Wolf and Winchester primers. I even sorted the ammo looking for no primers that were seated less than flush with the back of the case. I even got some factory from the shack and a friendly shooter next to me.

    Tonight I have sent an e-mail describing my problems to S&W. Being totally honest about my use of hand loads. I hope they won't give me a hard time about that but I hand load everything I shoot with the exception of rifle ammo. I just don't shoot enough to justify the cost.

    Any way I am hopeful that S&W will take care of it without fuss. I don't care if it needs a heavier trigger pull. As long as it goes bang every time the heavy trigger can be worked with. A FTF costs much more time than a heavy trigger.

    Thanks all for the help. The gun is so much fun when it works. So much for the revolver being the ultimate reliable gun. I will update when I hear from S&W.

    Here is a link to the S&W forum thread: http://smith-wessonforum.com/s-w-smi...pdate-2-a.html

    Any help I can get would be great. Thanks for looking, Sammy
  • #2
    not-fishing
    Senior Member
    • Jan 2009
    • 2270

    My primers seat a mm or so below the brass edge.

    Flush (not fully seated) might be the cause of light strike.

    I learned this the hard way. I always just keep firing until the nonfired bullet comes "back around on the guitar" and is restruck before I look for other causes.

    I had to do it a my IDPA Classifier a couple of days ago because I had lightened my hammer strike and was getting light strikes. Once I've shot through my CCI primers the next 5,000 primers are going to be Federals. (Jerrry Miculek suggested)
    Spreading the WORD according to COLT. and Smith, Wesson, Ruger, HK, Sig, High Standard, Browning

    Comment

    • #3
      golfrj
      Senior Member
      • Jul 2007
      • 1623

      Wolff makes what they call a Power Rib mainspring in two (2) strengths, normal & extra power.. You might try taking off the right side grip, backing out the mainspring screw and add a shim between the spring and the screw to see if more spring will help.. Good Luck..

      Comment

      • #4
        missiondude
        Senior Member
        • May 2008
        • 1646

        Are your moon clips bent? If you bent them stripping out the old rounds, or installing the new ones, that can cause the misfires. Are you sure your strain screw has not backed out again? I had the same problems with my 625, but I had the screw moved and action done, so it was my fault for not getting the screw locked in place.

        they are a great shooting gun when they work
        sigpicThe right of the people to keep and bear arms shall not be infringed. The original common sense gun law...

        Comment

        • #5
          michaels
          Member
          • Sep 2002
          • 101

          if your 625 has the lock, check it to make sure it didn't move and is slowing down the hammer fall. Better yet, take the damn think out and try the gun, since you reload, load up some cases without powder and bullet, you will probably only get one to go off at a time in the moon, the primers have a tendancy to back out a little. But this will allow you to at least tinker with gun without having to make a trip to the range. On a few of the newer 625's there were issues with the hammer rubbing inside the gun, pull the side plate and check it out.

          good luck with it

          michaels
          Michael Sousa

          Comment

          • #6
            jdg30
            Senior Member
            • Nov 2009
            • 1095

            I would just send the gun back to S&W and have them fix it. If the gun won't function right when stock then there's something wrong with it. Instead of spending extra money trying this and that, just send it to them and they should fix it. S&W pays shipping both ways for warranty returns/repairs.

            By the way, their factory is closed for the rest of this week for their annual 2-week shutdown so you might not get a response back to your email for a while.

            Comment

            • #7
              redcliff
              Calguns Addict
              • Feb 2008
              • 5676

              Unless you have a mechanical problem like a defective lock, short firing pin, etc.. the answer seems pretty obvious; you need more mainspring pressure.

              You can try a longer strain screw/set screw or you can quit fooling around and get a heavier mainspring and save the lighter mainspring for competition only use with handloads crafted with primers designed to function with light strikes.
              "You keep using that word. I do not think it means what you think it means."
              "What we get away with isn't usually the same as what's good for us"
              "An extended slide stop is the second most useless part you can put on a 1911"

              "While Ruger DA revolvers may be built like a tank, they have the aesthetics of one also,
              although I suppose there are a few tanks which I owe an apology to for that remark"

              Comment

              • #8
                sammy
                Veteran Member
                • Oct 2006
                • 3847

                I have tried the Apex firing pin and the Cylinder & Slide with poor results.

                The moon clips are factory new S&W and are not bent. I have about 20 of them and they all fail to fire.

                Well I got a call tag from S&W. I will post back when it returns. Thanks!!! Sammy

                Comment

                Working...
                UA-8071174-1