---
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
---
Collapse
X
-
It is worth the money since 9mm 1911's are fairly pricey in this state. If you don't feel like wasting the time to fix it up, I am sure a tinkere, such as myself, would be more than happy to take it off your handsSo my dad transfered a few pieces over to me. Among them was a thompson 1911 in 38 super. Its in pretty rough condition. I tried giving it a once over with a cleaning kit and brush. I took out most of the surface rust and carbon build up, but still definitely not something up to my standards. I was thinking of making it a project piece. Ie having it refinished and convert it into a 9mm for plinking. Worthwhile or waste of $
.
Originally posted by BumslieHK - the best 600 dollar gun, 900 dollars can buy.Originally posted by SleighterGetting legal advice from a gun salesman, is like getting medical advice from a janitor at a hospital. Both make about the same per hour and both prove that being around something all day doesn't make you an expert.
Lifetime NRA member. -
If it were me I'd have it refinished by one of the top shops....a great blue job is still under $300 in some places. Then once looking good you can buy a 9mm barrel for $55/60 and some magazines....then you have a 1911 9mm which looks good and can be a good shooter too.Comment
-
Thompson is fine - just as good if not better then any of the imported stuff (RIA, SA, etc.) - I think the frame is forged. Should be a mil-spec series 70 style pistol.
Convert it to 9mm - or sell it to me cheap and I will do it.
I think you can do a .40 conversion, but I'm not sure it's as easy as the 38 super to 9mm conversion.
JeffComment
-
I vote for refinishing it cheap and ugly and keeping it .38 Super, which is a nice hot-rod round that treads on .357 Magnum territory.
If it were mine, the only reason to go 9mm would be if I already had a pallet of cheap blasting 9mm ammo sitting around. Which I don't.I meant, it is my opinion that...

I do believe that where there is a choice only between cowardice and violence
I would advise violence. - M. Gandhi
You're my kind of stupid. - M. ReynoldsComment
-
This only works if you reload and even if you do, losing a dozen pieces of 38 super brass while on the range will ruin your day. 38 super is a fantastic round and was THE thing in defensive handgun shooting because it makes major power with very low recoil, but it's expensive to run and I would say untenable if you don't reload.I vote for refinishing it cheap and ugly and keeping it .38 Super, which is a nice hot-rod round that treads on .357 Magnum territory.
If it were mine, the only reason to go 9mm would be if I already had a pallet of cheap blasting 9mm ammo sitting around. Which I don't.Comment
-
You can get a Kart EZ fit barrel for under $200 and do it yourself. I looked into this myself because super is expensive to shoot and I definitely don't want to reload. Some say change the ejector others say it's not necessary , and maybe change magazines, either way not expensive.sigpicComment
-
40 is doable. The Super rim is a bit small than a 40 but depending on the tolerance in the slide and the tension on the extractor it might function fine. If not the breechface can be opened slightly to make it correct.
Thompsons are fine, as good as any.where are my pistol mags?Comment
-
Personally I'd sell it and buy a 9mm 1911. I never felt Auto Ordnance 1911's were that great to begin with and you could end up spending $400-500 to rebarrel and refinish it and replace the front sight. The rear sight installation is not so great; certainly not a properly "buried" Bomar.
Sell it for $350/whatever and put that and the money you would of spent on it towards a Springfield loaded 9mm and have a lifetime warranty or buy a good used Colt in 9mm."You keep using that word. I do not think it means what you think it means."
"What we get away with isn't usually the same as what's good for us"
"An extended slide stop is the second most useless part you can put on a 1911"
"While Ruger DA revolvers may be built like a tank, they have the aesthetics of one also,
although I suppose there are a few tanks which I owe an apology to for that remark"Comment
-
After thinking it over, I am leaning towards keeping it. I figure it would be a good project to get familiar the ins and outs of 1911 platform. Plus being the tinkerer I am, I'll take a resto mod approach.
Step 1: Function test. I figure I could swing by the range and try out a few rounds of this fabled 38 super. Any major problems revealed = bail out time.
Step 2: Break down. Pending a hopefully successful shake down, strip down the pistol to bare frame and slide, and baggie up the parts.
Step 3: Refinish: I have been looking around, and I really like some of the flat black pieces I have seen. Attatched below is a very nice example of the look I would like to achieve. Flat black with Stainless controls. Recommendations on place to refinish???
Step 4: New parts. Never satisfied with standard parts I was looking around and came up with the following shopping list.
- 9mm barrel(Kart?)
- Wilson combat:
trigger
beavertail
hammer
safety
slide lever
magazine release
- sights??? liking the combat style ones.
- 9mm magazines
- grips
Step 5: assembly required.
Step 6: duh...winning =p
Im sure this wont be an exact plan of action but at least a rough course of action. Thinking, new parts/smithing/assembly/retake down before coating perhaps. Anywhoo...I'll update as this goes along.Last edited by huee; 06-12-2011, 10:27 AM.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,746
Posts: 25,175,467
Members: 358,862
Active Members: 5,399
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 30316 users online. 31 members and 30285 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment