Unconfigured Ad Widget

Collapse

Installing Glock Sights

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sava
    Senior Member
    • Aug 2009
    • 508

    Installing Glock Sights

    I just bought 3 sets of Trijicon 3-Dot Steel sights for my G17, G19, and G22 and want to have them installed by someone.

    I called some of the local shops and am getting quotes of $50+ PER gun. It's not all that hard to install these sights if you have the sight pushing tool....right?

    Anyone know anyone in the Sacramento area that can install these for cheaper than $50 a pistol? I can't figure out why it would cost so much to install a simple pair of steel sights....

    Help?
  • #2
    BamBam-31
    CGN/CGSSA Contributor
    • Dec 2005
    • 5318

    You can do it yourself if you have a sight pusher or vise (and hammer and brass punches). Front sight is usually attached with a screw from the bottom (and some red loctite), while the rear sight is simply drifted in. Hardest part is getting the rear sight in the right place (a problem easily alleviated at the range w/ a sight pusher).

    People charge that much because other people will not be bothered to learn how to do it themselves. Plumbers, mechanics, tax guys, etc., same thing.
    sigpic

    Comment

    • #3
      barrym66
      Senior Member
      • Mar 2009
      • 2228

      $50 is not an unreasonable amount for sight installation. It takes about 45 minutes, with the right tools, including zero/alignment. So $50 is not an unreasonable charge, IMHO.

      After paying $65 for the same, I bought a used Glock sight pusher tool and have done 4-5 sets since. The factory tool lists for $140, but can be found used for less if you look around (I paid $45). Warning, some aftermarket rear sights (Heinie's) cannot be installed with the factory pusher, just FYI. And +1 on using loctite on the front sight threads, I lost one during a match and had to finish up the last 2 stages without it...not fun!
      Last edited by barrym66; 02-15-2011, 8:04 PM.
      Barry

      sigpic

      "Environmentalists look at the gun, the car and the jet engine as instruments of Satan, but the mosquito has killed more than all three put together." Jeremy Clarkson, on the green movement

      Thomas Jefferson

      Comment

      • #4
        ChrisTKHarris
        Veteran Member
        • Sep 2009
        • 4203

        What shop did you go to in Sac?
        Don't let the name fool you...

        Comment

        • #5
          elSquid
          In Memoriam
          • Aug 2007
          • 11844

          Originally posted by sava
          I just bought 3 sets of Trijicon 3-Dot Steel sights for my G17, G19, and G22 and want to have them installed by someone.

          I called some of the local shops and am getting quotes of $50+ PER gun. It's not all that hard to install these sights if you have the sight pushing tool....right?
          Yup.

          The right tool helps:



          But you can get by without it.

          A file is also useful for some rear sights. A bit of loctite for the front sight threads. Easy-peasy.

          -- Michael

          Comment

          • #6
            sirgiles
            Senior Member
            • Oct 2008
            • 2311

            lc action in san jose will only charge you $10.
            "I'm not in this world to live up to your expectations and you're not in this world to live up to mine."

            Bruce Lee

            Comment

            • #7
              unamused
              Senior Member
              • Mar 2009
              • 533

              Originally posted by barrym66
              $50 is not an unreasonable amount for sight installation. It takes about 45 minutes, with the right tools, including zero/alignment. So $50 is not an unreasonable charge, IMHO.

              After paying $65 for the same, I bought a used Glock sight pusher tool and have done 4-5 sets since. The factory tool lists for $140, but can be found used for less if you look around (I paid $45). Warning, some aftermarket rear sights (Heinie's) cannot be installed with the factory pusher, just FYI. And +1 on using loctite on the front sight threads, I lost one during a match and had to finish up the last 2 stages without it...not fun!
              how are they going to zero and align it without actually shooting it?


              as for the price... 50 per gun sounds ridiculous considering the tool costs about 100 new!

              you may as well just buy the tool, plus that way you can adjust it yourself at the range.

              Comment

              • #8
                sava
                Senior Member
                • Aug 2009
                • 508

                Originally posted by ChrisTKHarris
                What shop did you go to in Sac?
                Just Guns & TDS Guns.

                I dont want to invest $100 into a tool that I will use once, and I also don't want to spend $~150 for the installation of some sights.

                Damn. Decisions...decisions

                Comment

                • #9
                  swrdply400mrelay
                  Member
                  • Aug 2010
                  • 250

                  Originally posted by sava
                  Just Guns & TDS Guns.

                  I dont want to invest $100 into a tool that I will use once, and I also don't want to spend $~150 for the installation of some sights.

                  Damn. Decisions...decisions


                  You could always sell it and get some of that money back.

                  Comment

                  • #10
                    barrym66
                    Senior Member
                    • Mar 2009
                    • 2228

                    Originally posted by unamused
                    how are they going to zero and align it without actually shooting it?

                    as for the price... 50 per gun sounds ridiculous considering the tool costs about 100 new!

                    you may as well just buy the tool, plus that way you can adjust it yourself at the range.
                    As mentioned, just buy the tool....or find a shop that does it for less. Most shops that charge $10 require that you buy the sights from them. Just sayin'....

                    Rough alignment is done with a boresighting tool...with the right tools and experience, the alignment is usually pretty much right on. The advantage of having the pusher yourself is you can then shoot a few rounds and use the pusher to zero in.
                    Barry

                    sigpic

                    "Environmentalists look at the gun, the car and the jet engine as instruments of Satan, but the mosquito has killed more than all three put together." Jeremy Clarkson, on the green movement

                    Thomas Jefferson

                    Comment

                    • #11
                      elSquid
                      In Memoriam
                      • Aug 2007
                      • 11844

                      Originally posted by sava
                      Just Guns & TDS Guns.

                      I dont want to invest $100 into a tool that I will use once, and I also don't want to spend $~150 for the installation of some sights.

                      Damn. Decisions...decisions
                      You can get by without the tool.



                      Click on "videos" for step-by-step instructions.

                      -- Michael

                      Comment

                      • #12
                        BamBam-31
                        CGN/CGSSA Contributor
                        • Dec 2005
                        • 5318

                        Actually, I use calipers to center the rear sight as much as possible in the rear notch (equal gaps on both sides), and it's usually pretty close. Haven't really needed the sight pusher yet, but I do already own the vise, hammer, punch set, and calipers.
                        sigpic

                        Comment

                        • #13
                          Atomic Donut
                          Senior Member
                          • Sep 2010
                          • 802

                          if you ever in contra costa county i got the pusher tool to instal it yourself.

                          Comment

                          • #14
                            meangreen46
                            Senior Member
                            • Jul 2010
                            • 603

                            Originally posted by sava
                            I can't figure out why it would cost so much to install a simple pair of steel sights....

                            Help?
                            Places will charge you because you didn't by them from their store. I know most places down here in SoCal would install them for free if bought from the same store.

                            Comment

                            • #15
                              itzjere
                              Member
                              • Jan 2011
                              • 259

                              PM inbound of a guy in Sac that will do it free of charge.

                              Comment

                              Working...
                              UA-8071174-1