I got an older mark II awhile back from my father and it doesn't feed right. The bolt or whatever gets stuck halfway backwards and fails to load another round after firing. Any thoughts on this?
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Ruger Mark II problems
Collapse
X
-
Is it clean? I'd shoot the slide area with something like break free or similar, to clean it up and maybe replace the mag with a new one, that should fix it up. .22 is DIRTY ammo, but mine has never missed a beat.
My guess is dirty internals and/or weak mag spring.Originally posted by tony270It's easy to be a keyboard warrior, you would melt like wax in front of me, you wouldn't be able to move your lips.Originally posted by repubconservPrint it out and frame it for all I careOriginally posted by el chivoI don't need to think at all..XXXXXXXXXXXXXXXXXXXXXXXOriginally posted by pjsigYou are talking to someone who already won this lame conversation, not a brick a wall. Too bad you don't realize it.
sigpic -
Hard to guess what the problem is without seeing the gun but when my Mark II gets dry and dirty, the bolt moves like it's in slow motion.
A Mark II or III needs some oil rubbed on the bolt and the receiver where the bolt travels needs to be clean.
Other than that, take a look at the ejector (the thing that is riveted to the frame) and make sure it's straight (and doesn't turn) and in line with the grooves in the bolt.Comment
-
Can you cycle the gun manually and pick up a fresh round? Does it fail to feed all the time? What kind of ammo are you using?
Rimfire pistols can be finicky with ammo. Try some CCI Minimags. For some reason, Minimags will run in just about anything. If a gun won't run with Minimags, then I know the problem is somthing other than ammo.
Randy
NRA Life MemberNRA Life Member
CRPA Life MemberComment
-
What kind of ammo are you using in it? (brand and type) Sometimes they can be finicky depending on ammo. As mentioned before, sometimes they are just dirty, but now that you've cleaned it, make sure the bolt moves back and forth smoothly and quickly. Also, if you're not using hot enough ammo, it won't cycle the bolt completly. Just to be clear....is it ejecting cleanly? If so is next round "stove piping" up against the breech or is the bolt not going all the way back and picking up the next round? Basically closing on an empty chamber. You man not need to go and get a mag yet until we have some more info. The mag may just need a little fine tuning. c goodComment
-
if the mag is sitting too high, you can file the base plate of the mag down a little bit so it will sit lower.
Cheaper than buying a new mag, and an easy part to replace if you mess it up.If it was a snake, it would have bit me.
Use the goog to search calgunsComment
-
Yeah, stovepiping-the round is getting sandwiched in there with the bullet tip above the breach. One time it looked like the bolt didn't come all the way back as well.
I'm developing a hatred of this goddamn thing every time I take it apart and put it back together as the F**&(*&ING safety keeps sticking or something. Can't cock it now. Have to remember to say thanks to my dad for this paperweight.Comment
-
Insert the magazine and see if the rear magazine lips on the left hand side is at the same elevation as the ejector. If so, file the sharp edge and top of the lip just a little to allow a clearance. You may also want to take a good look at the extractor. Make sure the spring gives it tension and the hook is all there.Comment
-
Stove pipes usually are caused by the magazine lips being to "open" in the front. Imagine all the number of rounds being fed out of that area over the years. The "lips" are the very most forward part of the metal part of the mag that guide the next round into the chamber. Sometimes all it takes is a little readjusting of these two parts. Normally I take a pair of needle nose pliers and give them a little twist down working from the front part of the mag. Be careful not to create any burrs with the pliers. If you do, just take a little 400 wet/dry paper and polish it up. HTH c goodComment
-
Are you absolutely SURE that you are assembling it correctly? If you read the instruction manual it details the rediculous process of turning the gun upside down and dry firing it before inserting the bolt. If you missed this step, it can and will cause the symptoms you have described.Comment
-
Ruger assembly complications led me to the Browning Buckmark. I'm glad I made the choice. Now I have to find some ammo it likes! Are ALL .22's finicky about ammo?"We're surrounded. That simplifies our problem. We can now fire in any direction and strike the enemy." ....Colonel Lewis Burwell "Chesty" Puller, Commanding the 1st Marine Regiment at The Battle of The Chosin Reservoir, Korea 1950Comment
-
I'm pretty sure I put it back together correctly. All the peices fit & it cocks and fires. I read the manual and it took me at least half a dozen tries to get it back together properly.Are you absolutely SURE that you are assembling it correctly? If you read the instruction manual it details the rediculous process of turning the gun upside down and dry firing it before inserting the bolt. If you missed this step, it can and will cause the symptoms you have described.
I will be buying a 22 revolver for a plinker...Comment
Calguns.net Statistics
Collapse
Topics: 1,870,887
Posts: 25,177,193
Members: 358,862
Active Members: 5,395
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 38425 users online. 125 members and 38300 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment