P365 Grip Module

[chetly]

After taking the P365 out shooting, I found that the factory grip module, even with the pinky extension was on the short side and my pinky went below the mag leaving only two fingers holding the grip. After doing some research I found that Armory Craft makes a mag baseplate that allows you to run the 10 round mags in the X grip module. I did remove the mag disconnect but left the manual safety. Doing so, the grip length is 5/8in longer. A lot more stability holding the gun and makes the gun more confidence inspiring to shoot.

[newbutold]

Nice.

[Interpol]

You can also use OEM Sig 365XL mags with the baseplate adapters.

[sigstroker]

More grip = less concealment.

[Palmaris]

I do not carry too long, but I have great friend which carries for years and I do as he suggest. So far I am please with his advises-best lenght in balance between concealment and performance will be XL/XMacro chopped to XL lenght.
Regarding concealment-try PHlster Enigma belt system-there is nothing to compare in anyway you can imaging.

[static2126]

Get an xl or chop a macro to xl, toss it on an enigma and you should be set.

Carry that setup 6am to midnight daily

[Palmaris]

Get an xl or chop a macro to xl, toss it on an enigma and you should be set.

Carry that setup 6am to midnight daily

This is guy is my mentor on CCW stuff. Trust his words!

[Tere_Hanges]

I didn't even bother with the standard grip that came with my CA version 365. I ordered an X/XL grip module and two base pads that extend 10rd standard mags to X/XL length, before I even picked up the gun. As soon as I got it home, I removed the MDM (super easy and quick to do) and put the FCU in the X/XL grip module.

IMHO the standard grip is unnecessarily too short. The X/XL grip length is perfect. Really wish Sig had just added the P365X to the roster instead. Sure, with a pinky extension a standard grip will be close to X/XL in length, but I really hate pinky extensions as a method of extending the grip length. Might as well just have a longer grip and a flush fitting magazine.

[Carl88]

because finger extensions do not add any material to the back which contributes to printing. sigs suck. get a shield plus and then order the oem butt plate, finger rest directly from them:

[Palmaris]

I didn't even bother with the standard grip that came with my CA version 365. I ordered an X/XL grip module and two base pads that extend 10rd standard mags to X/XL length, before I even picked up the gun. As soon as I got it home, I removed the MDM (super easy and quick to do) and put the FCU in the X/XL grip module.

IMHO the standard grip is unnecessarily too short. The X/XL grip length is perfect. Really wish Sig had just added the P365X to the roster instead. Sure, with a pinky extension a standard grip will be close to X/XL in length, but I really hate pinky extensions as a method of extending the grip length. Might as well just have a longer grip and a flush fitting magazine.

Most likely Sig already molded couple of milliones and now they can get rid of them. When my wife had rona and lost sense of smell and taste-I used on her all bad tasted coffee pods we had for Keurig. this is how I found she recovered-she screamed ?what kind of **** I brewed for her?!

[Dennis]

My thinking was, if your going to carry with a larger base plate, its better to incorporate that length in the grip itself. I went with an Armory Craft X grip. It's just under 2.5" in length. It makes mag changes easier for me. However, it sill doesn't allow all of my pinky on the grip. It is much more comfortable and secure in my hand.

[Tere_Hanges]

When my wife had rona and lost sense of smell and taste-I used on her all bad tasted coffee pods we had for Keurig. this is how I found she recovered-she screamed ?what kind of **** I brewed for her?!

Oh dang, that's funny.

[Palmaris]

because finger extensions do not add any material to the back which contributes to printing. sigs suck. get a shield plus and then order the oem butt plate, finger rest directly from them:

I picture is way too small to verify if this Sig. looks like piece of cr.p, not sig. Can you please make picture bigger so we can verify?

[static2126]

because finger extensions do not add any material to the back which contributes to printing. sigs suck. get a shield plus and then order the oem butt plate, finger rest directly from them:

Imo shield plus is 2nd best small gun (after p365l. The 13 round mags do have a tendency to have ethe baseplate pop off though

[BOBGBA]

Oh dang, that's funny.

It's genius, if you ask me.