Springfield 1911 Ultimate Carry

[still919]

I know its already been relayed, but yes, it's totally normal. I would like to add another option though. If you are not in a hurry to get shooting, you may want to consider a basic field strip and a routine cleaning/lube (I don't think you mentioned whether you did this or not). Reassemble, and cycle the slide by hand numerous times (say, while you are sitting around watching TV or something). Then repeat the process (field strip, cleaning/lube, cycle slide by hand).

Essentially, this is meant to facilitate the break-in process and reduce the chance of experiencing cycling issues with live ammo on a brand new firearm that was built to tight tolerances. This procedure actually comes recommended by certain companies who manufacture hand-built custom 1911s. Typically calls for a total of 100-150 slide cycles by hand.

But hey, everything may run flawlessly if you opt to start shooting right away, and I hope it does. Let us know how it runs for you.

[MarikinaMan]

It's defective. I will buy it from you for parts. 300 bucks. And I'm being generous.

[Peahi2]

I veto field stripping! If he can’t even rack the slide , he won’t be able to put it back together hell, he won’t be even be able to disassemble lol! trust me on this one. Lol. Hand cycling is no fun. Why buy a gun and not shoot it!? Trust in Springfield custom. Send rounds down range. You won’t regret it. I sent 1000+ rounds before cleaning with new Springfield custom and also a les Baer recently with no problems. Reassembling these tight guns is what shakes my soul though. Lol

[bb557]

As has been said, this is normal for a hard fit pistol. I have two Springer Professionals and they were both this way. Baer pistols also have this build philosophy.

As was stated, lube, load and shoot. Rinse and repeat. It will loosen up.

Have fun.

[JTROKS]

As has been said, this is normal for a hard fit pistol. I have two Springer Professionals and they were both this way. Baer pistols also have this build philosophy.

As was stated, lube, load and shoot. Rinse and repeat. It will loosen up.

Have fun.

Les Baer used to head Springfield Armory CS.

[bb557]

Les Baer used to head Springfield Armory CS.

I did not know that. Thanks!

[Pupulepeter]

[sirgrumps]

I know its already been relayed, but yes, it's totally normal. I would like to add another option though. If you are not in a hurry to get shooting, you may want to consider a basic field strip and a routine cleaning/lube (I don't think you mentioned whether you did this or not). Reassemble, and cycle the slide by hand numerous times (say, while you are sitting around watching TV or something). Then repeat the process (field strip, cleaning/lube, cycle slide by hand).

Essentially, this is meant to facilitate the break-in process and reduce the chance of experiencing cycling issues with live ammo on a brand new firearm that was built to tight tolerances. This procedure actually comes recommended by certain companies who manufacture hand-built custom 1911s. Typically calls for a total of 100-150 slide cycles by hand.

But hey, everything may run flawlessly if you opt to start shooting right away, and I hope it does. Let us know how it runs for you.

DO NOT FIELD STRIP!!!!

Shoot a minimum of 200 rd of hardball, preferably closer to 500 rd before ANY ATTEMPT AT DISASSEMBLY!!

Just wipe with a soft cloth and use lube generously on the frame/slide rails, and try to get some lube on the locking hood.

Even if it take a few months.

If you want wait for closer to 1000rd, even better.

Field strip and clean at that point.

Then only put the slide on the frame with a little Flitz and elbow grease.

It should slide like a precision bearing.
Then clean, lube, reassemble, and rack the slide over and over again.

It should run like a blade on fresh ice.

[BuddhaBar]

It's defective. I will buy it from you for parts. 300 bucks. And I'm being generous.

lmfao.... Let me think about it....

[still919]

Well...don't leave us hanging. SeniorGrumps and I want to know what happened?

[BuddhaBar]

I was able to return, but I think I "pulled the trigger" early before some of you responded. Only reason they took the return was because I didn't DROS it yet. Left it at the store while figuring out what to do. Now that I hear what you guys have to say, may change my mind and pick it back up again.

[AFTII]

I've used Microlon assembly lube on new Les Baers and it slicked them right up. However, when I tried it on a Springfield Professional, the Springer was still tight. It's a quick fix if it works.

I just applied a bit to the tip of a Q-tip and brushed it on the outside of the last 1/2" of the barrel and inside the barrel bushing. You can use it on the rails, but that is not where the slide is sticking. A little goes a long way. Don't overdo it.

https://microlon.com/collections/lubes-greases/products/microlon-assembly-lube