Unconfigured Ad Widget

Collapse

Need help on Glock/Zev adjustable trigger

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tsoiky
    Senior Member
    • May 2013
    • 852

    Need help on Glock/Zev adjustable trigger

    Put in the adjustable trigger kit (in factory setting, didn't touch the set screws) on G17 frame, Suarez aftermarket slide.

    Function checked, reset ok. Tested fire today and loaded with 5 rounds each time.

    10 out of 3 times, it went rock n rolls. Luckily I was at outdoor range and lot of 308s with muzzle brakes at the range, the RSO didn't heard it and I wasn't kick out from the range. Anyway I packed the gun and didn't wanna try no more.

    Any insight where to check first? Seems like the sear is not catching the firing pin.

    Slide, trigger bar, factory setting etc... out of spec???



    Sent from my iPhone using Tapatalk
  • #2
    Rhyme_merchant
    Member
    • Dec 2014
    • 248

    How did the gun work before you changed every part?

    Comment

    • #3
      nedro
      Veteran Member
      • Nov 2014
      • 4130

      How about explaining in English?
      Not an insult. I simply have no idea what you are talking about.
      BTW, I own a zev adjustable and would like to help.

      Comment

      • #4
        tbc
        Calguns Addict
        • Jun 2011
        • 5955

        So you put a ZEV adjustable trigger into your G17 and it went full auto 3 out of 10 times.

        Comment

        • #5
          tsoiky
          Senior Member
          • May 2013
          • 852

          Yes it went full auto


          Sent from my iPhone using Tapatalk

          Comment

          • #6
            nedro
            Veteran Member
            • Nov 2014
            • 4130

            OK.
            Do you hear/feel the reset?
            Can you manually push the trigger forward to here the reset?Take the connector out and take a picture of it from the side and also from the top.
            Also take a pic of the under side of the slide.
            I think the tab next to the disconnect ramp is broken or bent.
            I just had mine out two nights ago for some polishing of the connector and dis-connector.
            If the tab is bad, it will not reset and your sear will stay off of the firing pin, causing auto-fire.
            Last edited by nedro; 12-14-2016, 10:44 AM.

            Comment

            • #7
              tsoiky
              Senior Member
              • May 2013
              • 852

              Originally posted by nedro
              OK.
              Do you hear/feel the reset?
              Can you manually push the trigger forward to here the reset?Take the connector out and take a picture of it from the side and also from the top.
              Also take a pic of the under side of the slide.
              I think the tab next to the disconnect ramp is broken or bent.
              I just had mine out two nights ago for some polishing of the connector and dis-connector.
              If the tab is bad, it will not reset and your sear will stay off of the firing pin, causing auto-fire.


              Thanks I will take some pics after.

              I can feel the reset when the gun behave normally. I also think the tab next to disconnect ramp (or the slide cut) is out of spec a little bit. Seems like it doesn't push the sear high enough to catch the firing pin.


              Sent from my iPhone using Tapatalk

              Comment

              • #8
                nedro
                Veteran Member
                • Nov 2014
                • 4130

                The disconnector should not be touching the top of the plastic block it is secured to. If that is the case, it might be why it's doing that.
                The tab on top pushes the disco (towards the center line of the gun) out of alignment so that the connector can't stay down. If it doesn't fully disengage the connector, you get what you described.

                Comment

                • #9
                  nedro
                  Veteran Member
                  • Nov 2014
                  • 4130

                  why not simply polish the stock pieces for nothing?
                  I've done all three.
                  He has a good trigger. Whatever is going on, is probably a simple fix.

                  Comment

                  • #10
                    spoolinq
                    Member
                    • Feb 2009
                    • 328

                    It's the connector. Email them and they'll mail out a new one.
                    Last edited by spoolinq; 12-14-2016, 11:32 PM.

                    Comment

                    • #11
                      _TomT_
                      Veteran Member
                      • Jun 2013
                      • 3354

                      Did you do like the instruction said, which is turn the over travel screw out 1/4 a turn before you install the trigger? If the overtravel set a bit too much the gun will fail to reset and go full auto.

                      Comment

                      • #12
                        nedro
                        Veteran Member
                        • Nov 2014
                        • 4130

                        Tom,
                        I understand what you are saying. But for that to happen , wouldn't the connector also need to come up onto the striker then back off of it?
                        Or are you talking about a bump fire?
                        tsoiky,
                        If you have the stock trigger spring. Try switching it out. Sometimes the trigger spring is too strong and will allow auto fire.

                        Comment

                        • #13
                          Packy14
                          Calguns Addict
                          • Jul 2008
                          • 5312

                          Did you check the safety functions prior to using (YouTube it on how to check). You probably have the reset screw to far in and you aren't engaging safety. Zev is expensive trash by the way.
                          NRA Lifetime Member

                          1A-2A = -1A

                          Comment

                          • #14
                            tsoiky
                            Senior Member
                            • May 2013
                            • 852

                            I used the 3lbs striker spring which comes with the package. The trigger feels great, function check no issue at all. I like this trigger and wanna make it works.

                            Did some research last night. I will look into the pre travel set screw.

                            However it is pain in the *** to re adjust, go to the range and gun not working. I don't like the idea to strip the gun at the range but I may have no choice.


                            Sent from my iPhone using Tapatalk

                            Comment

                            • #15
                              osis32
                              Calguns Addict
                              • Jul 2009
                              • 5912

                              at least glocks are super easy to strip. you can figure it out in no time I'm sure.
                              Just a libertarian guy in a Leftist Authoritarian state.

                              Comment

                              Working...
                              UA-8071174-1