Ghost Trigger Connectors

[JS41989]

I've been looking at some of the different Ghost connectors... Ultimate, Edge, and Evo Elite. From what I've read the Ultimate and Edge are drop in connectors. The only real difference I can find is that the Edge gets rid of the "bump" in the trigger pull. Is there anything else I'm missing. Also, I know the Evo Elite requires some fitting. Can anyone share if there's a huge benefit to this connector?

**Going to pair whichever one I order with a 6 pound trigger spring and 6 pound firing pin spring.**

[JS41989]

I will look into these!

[SJulian10mm]

Don't like Ghost connectors. Get the TTI one here. Been using it for almost 2 1/2 years.

^
This - Iv been much happier with the Glock 3.5 connector, haven't tried the setup he linked but it sounds good and its got some top shooters backing it. Ghost stuff gets a lot of hype but doesn't deliver IMO, their spring kit caused nothing but light strikes in my G34 and their whole spring/connector kit didn't even get me under 5lbs of pull.

[Bill Steele]

I have Ghost Rocket connectors in most of my Glocks (the one where you fit it by grinding the tab down to get over travel the way you want it). I have found them to be reliable and to my taste.

I also polish everything up and run a lighter safety plunger spring and heavier trigger spring in most of my guns. Some, I have run lighter striker springs (probably the most reduction in trigger weight is achieved here, but also usually need a lightened striker for reliable ignition; in the end, I have found light striker springs/strikers more trouble than they are worth on paper).

[Rhyyke]

Don't like Ghost connectors. Get the TTI one here. Been using it for almost 2 1/2 years.

Does the TTI kit offer a significantly cleaner trigger pull than a oem minus connector?

[static2126]

I favor the oem.minus connector.

Ghost is hit or miss. Friends either love theirs or have issues.

[jkody]

Had a Ghost in a 19 for a while, felt wierd so I replaced with an Glock minus.

[mcat707]

I had Ghost connectors in most of all my Glocks. Worked fine until I had one installed in a Glock 30S and a Glock 41. After firing a round the trigger would not reset on either of them. (I have installed my fair share of OEM and aftermarket connectors so this was not my first rodeo.) I reinstalled the Ghosts to make sure it was installed correctly. Same problem continued on.

After that experience with Ghost connectors I took them out of all my Glocks that had them and switched to the OEM minus (-) connectors and never looked back. They all now sit in my extra gun parts crate.

YMMV

[JS41989]

Anyone know where I can find the OEM minus connector online?

[static2126]

Anyone know where I can find the OEM minus connector online?

Google glock oem minus connector..tons of places sell. Believe amazon does too

[SJulian10mm]

Amazon

[JTROKS]

Last I installed was an Evo that required fitting the tab for over travel. After all the work the end result was 2.5 lb clean and light pull. The trigger is polished OEM.

[Bill Steele]

Anyone know where I can find the OEM minus connector online?

http://www.glockmeister.com/45-Pound-Stock-Connector/productinfo/G721/

http://glockparts.com/Glock%20original%20minus%20connector_it-6648.aspx?CAT=705

Here their knock off:

http://glockparts.com/Glock%20original%20minus%20connector_it-1104824.aspx?CAT=705

[JS41989]

http://www.glockmeister.com/45-Pound...ductinfo/G721/

http://glockparts.com/Glock%20original%20minus%20connector_it-6648.aspx?CAT=705

Here their knock off:

http://glockparts.com/Glock%20origin...4.aspx?CAT=705

Thanks for the links. I know I could find them on Amazon and what not but I was trying to avoid any knock offs.

[Sam]

Does the TTI kit offer a significantly cleaner trigger pull than a oem minus connector?

My TTI examples felt much smoother than an OEM minus connector upon installation.