Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > INTERESTS AND ACTIVITIES > Gunsmithing & How To
Register FAQ Members List Calendar Mark Forums Read

Gunsmithing & How To Pro, Amateur & WECSOG and Tutorials, Guides & OLL Build Instructions

Reply
 
Thread Tools Display Modes
  #1  
Old 11-21-2020, 5:57 AM
Sailormilan2 Sailormilan2 is online now
Veteran Member
 
Join Date: Nov 2006
Location: Bakersfield, CA
Posts: 3,331
iTrader: 8 / 100%
Default Making a hinged trigger guard for a Yugo Mauser.

I had been tossing around the idea of making a hinged TG for my Yugo Mauser in .243 Win. I got the idea when I realized that the distance from the rear magazine wall to the rear guard screw was the same, whether it was an Intermediate Yugo or a standard 98. The difference in length is all in the front end, basically from about the mid point of the magazine to the front screw. So, I got the idea of finding a donor hinged TG, and doing some cutting and welding.
Well, I've had the donor for months now, and finally worked up the courage to do it. Realizing that I don't do this often, and I'm not trained, some of my ideas might not be the most efficient.
1st I hacked off the trigger guard off the donor at the rear mag wall. I ruined a previous Yugo TG, by cutting it in the wrong place, so I was very cautious and conservative today. I cut the military TG right in front of the trigger guard itself. I used an old Yugo stock as a fitting jig, and when placed in there, I had over lap. I ended up cutting the donor TG, with the latch, right at the latch. On the military unit, I had to trim back all the way to the mag catch/spring tunnel at the back of the rear wall. I actually had to remove some of the tunnel for everything to fit. Once everything fit, I beveled the edged for a good weld. I would have preferred a TIG welder, but I didn't know anyone who had one. So, my neighbor and his MIG welder got drafted. Unfortunately, there wasn't any real support for the military unit, so it got slightly out of position during welding. Resulting in a slight downward tilt at the weld. But, that won't affect anything, and when in the stock, it's not noticeable. We also filled the front locking screw hole. Which I cleaned out with a special cutter.
So far, I've ground down the welds on the sides, so they match the stock contours. Ground down the front screw hole fill, and still have a little to do. I used a 1/4" end mill to open up the hole for the hinge on the floor plate to fit into. Opened with 1/4", then cleaned up a bit with a 5/16". Then filed the end of the cut out square and with an angle inside. Hinge pin hole was drilled a while ago.
Currently I've filed down the latch end of the floor plated once I got it to latch. For some reason, Mausers have a 1/2" square cut just in front of the front mag wall. That leaves very thin metal where the hinge pins will be going. So, my thoughts on that are once everything is done, short of refinishing, I'm going to bead blast all the parkerizing off. Then coat the floorplate hinge tongue with Brownells release agent, put the floor plate in place with the hinge pin, then pack DevCon Steel bed into the space to give extra support. Rifle will be finished in parkerizing, and I don't believe that the parking solution will affect the DevCon.
I still need to find a donor, sacrificial 7.64 drill bit for the front hinge pin, and profile the rear sides.
Here it is, all parked to match the rifle, and just needing the hinge pin.
Attached Images
File Type: jpg 20200924_133940.jpg (95.3 KB, 42 views)
File Type: jpg 20200924_133924.jpg (97.8 KB, 35 views)

Last edited by Sailormilan2; 11-21-2020 at 5:59 AM..
Reply With Quote
  #2  
Old 11-27-2020, 8:05 AM
jtv3062's Avatar
jtv3062 jtv3062 is offline
Veteran Member
 
Join Date: Oct 2005
Posts: 2,669
iTrader: 0 / 0%
Default

I think Larry does a video on YouTube doing this.
__________________
Do not fear the enemy, for your enemy can only take your life. It is far better that you fear the media, for they will steal your Honour
Let's pray for Obama Psalm 109:8






159
Reply With Quote
  #3  
Old 11-28-2020, 5:06 AM
Sailormilan2 Sailormilan2 is online now
Veteran Member
 
Join Date: Nov 2006
Location: Bakersfield, CA
Posts: 3,331
iTrader: 8 / 100%
Default

Actually, that looks like more work. Plus, there's a couple of problems with the video.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 6:12 PM.




Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2021, Calguns.net an Incorporated Company All Rights Reserved.
All opinions, statements and remarks made by Calguns.net on this web site and elsewhere are solely attributable to Calguns.net.



Seams2SewBySusy