Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > FIREARMS DISCUSSIONS > Optics, Mounts, Rails and Sights
Register FAQ Members List Calendar Mark Forums Read

Optics, Mounts, Rails and Sights If it aims your firearm, post about it here.

Reply
 
Thread Tools Display Modes
  #1  
Old 08-12-2019, 11:01 AM
islandchanel's Avatar
islandchanel islandchanel is offline
Member
 
Join Date: Mar 2006
Location: San Diego/Riverside
Posts: 446
iTrader: 5 / 100%
Default Tips for mounting a scope.

Hello,

Just ordered my scope and rings and was wondering what do most people use to mount the scope properly. Any tips and advice on equipment needed would be appreciated.
Reply With Quote
  #2  
Old 08-12-2019, 11:15 AM
NorCalFocus's Avatar
NorCalFocus NorCalFocus is offline
Veteran Member
 
Join Date: Aug 2013
Location: Surprise, AZ
Posts: 3,920
iTrader: 12 / 100%
Default

Well...

1. I use a gun vise, or another way to secure the rifle.
2. I then torque the base to the action using the recommended specs provided by the manufacturer of the base.
3. I then use a scope leveling kit to level the action or scope base.
4. I place the bottom half of the scope rings on the base, place the scope in the rings and eye ball it into good spacing.
5. Then I'll add the top half of the rings, and tighten them down so they don't fall off, but the scope can still move.
6. I then get behind the rifle with my eye's closed, then opne them to see if the scope is set to my eye relief.
7. After that, I level to scope to the action/base level and torque the scope rings down to the manufacture's specs.

I'm sure I'm glossing over something, but thats the basic procedure to do it. A torque wrench and scope levels will run you about $50-$60. You can also just pay a gunsmith to mount it for about the same.
Reply With Quote
  #3  
Old 08-12-2019, 1:30 PM
islandchanel's Avatar
islandchanel islandchanel is offline
Member
 
Join Date: Mar 2006
Location: San Diego/Riverside
Posts: 446
iTrader: 5 / 100%
Default

Thanks for the tips
Reply With Quote
  #4  
Old 08-12-2019, 5:02 PM
boltstop's Avatar
boltstop boltstop is offline
Senior Member
 
Join Date: Nov 2007
Location: SF Bay Area
Posts: 668
iTrader: 5 / 100%
Default

To find the ideal ring height, gently clamp rifle in a level vice, stack quarters on the rail and balance the scope on them until the bell clears the barrel and you are happy with the cheek weld.
Reply With Quote
  #5  
Old 08-12-2019, 9:46 PM
Unforgiven's Avatar
Unforgiven Unforgiven is offline
Senior Member
 
Join Date: Aug 2009
Location: Sacramento Ca.
Posts: 791
iTrader: 33 / 100%
Default

Locktite.
__________________
The man who trades freedom for security does not deserve nor will he ever receive either.

Benjamin Franklin
Reply With Quote
  #6  
Old 08-13-2019, 9:49 AM
Divernhunter Divernhunter is offline
Calguns Addict
 
Join Date: May 2010
Location: Denair, Ca
Posts: 7,825
iTrader: 13 / 100%
Default

good rings and NO locktite.
Lap the rings for best fit.
__________________
A 30cal will reach out and touch them. A 50cal will kick their butt.
NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club & NAHA Member, Madison Society member
Reply With Quote
  #7  
Old 08-13-2019, 12:55 PM
RAMCLAP's Avatar
RAMCLAP RAMCLAP is offline
Senior Member
 
Join Date: Nov 2012
Location: Orange, CA
Posts: 2,209
iTrader: 2 / 100%
Default

If it's two separate rings they really need to be lapped.
__________________
Psalm 103
Reply With Quote
  #8  
Old 08-16-2019, 1:36 PM
CamW CamW is offline
Senior Member
 
Join Date: Oct 2005
Location: SGV
Posts: 1,210
iTrader: 102 / 100%
Default

Here's a video that someone posted from another thread.It may not be the same type of rings you have but it's an excellent video.


Last edited by CamW; 09-10-2019 at 8:12 PM..
Reply With Quote
  #9  
Old 08-26-2019, 9:26 AM
Surf.n.Turf Surf.n.Turf is offline
Junior Member
 
Join Date: May 2019
Posts: 27
iTrader: 0 / 0%
Default

Here's a few things I've picked up mounting and zeroing my scopes:
  1. SAFETY SAFETY SAFETY - make sure rifle is unloaded, mag clear, and ammo is in a totally different room than you so no accidents happen.
  2. Adjust scope placement as far forward as comfortable with good cheek weld to allow max eye relief
  3. Blue locktite - some use it, some don't. I have some hardware I've found that expands and loosens, so I use it. DO NOT get the red locktite ("permanent" rating)
  4. Cross-tighten your rings and mounts, doing a little at a time. Think of like drawing a star. Upper-left, bottom-right, bottom-left, upper-right. STOP if you feel resistance in any before all are snug
  5. Continue cross-tighten after feeling all are snug, 1/4 turn at a time. Hand tighten until very firm.
  6. Boresight your rifle after scope is mounted, BEFORE firing a single shot. You don't need a laser or anything fancy. Remove your rifle's bolt, and mount rifle on anything stable, pointing to something 10-25 yards away. I put it on my kitchen table on shooting bags. Look down thru barrel, aim muzzle at something recognizable with naked eye, take note of whatever is in center of barrel. Now tough part - without moving rifle at all, look thru scope. Adjust scope to aim on point of thru-barrel boresight. Repeat until the 2 sight pictures have the same center aim point. Save ammo, save time.
  7. Test boresight at range as close as possible. Start at 25, then 50, then 100 if possible. Adjust zero at each distance.
  8. If noticeably off aim at any time, STOP and assess the situation. Is the boresight vs scope center aim off? Are all screws tightened down equally? Is it shooter error from flinching or not a secure rest?
  9. When adjusting aim point, tap scope lightly before shooting next round to help stabilize adjustment. The adjustment springs may take 1-2 shots before they settle into their new stable position.

Good luck!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 6:15 PM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2018, Calguns.net an Incorporated Company All Rights Reserved.
Calguns.net and The Calguns Foundation have no affiliation and are in no way related to each other.
All opinions, statements and remarks made by Calguns.net on this web site and elsewhere are solely attributable to Calguns.net.