Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > INTERESTS AND ACTIVITIES > Gunsmithing & How To
Register FAQ Members List Calendar Mark Forums Read

Gunsmithing & How To Pro, Amateur & WECSOG and Tutorials, Guides & OLL Build Instructions

Reply
 
Thread Tools Display Modes
  #1  
Old 11-15-2012, 11:18 AM
esqui2809 esqui2809 is offline
Member
 
Join Date: Apr 2009
Posts: 102
iTrader: 13 / 100%
Default virgin barrel

After finishing my build, while cleaning my barrel I noticed a small piece of metal shaving left over from drilling the gas port hole. Will this affect the first round out of the barrel? Tried time knock it off w the rod but didn't want time damage the rifling next I will try a brush any suggestions?
Reply With Quote
  #2  
Old 11-15-2012, 11:51 AM
phrogg111's Avatar
phrogg111 phrogg111 is offline
Senior Member
 
Join Date: Jan 2012
Location: Folsom
Posts: 710
iTrader: 10 / 92%
Default

If you have a brass or carbon fiber rod, then a rod is a good option. Definitely use a brush.

I highly doubt it would destroy your barrel - but better safe than sorry.
__________________
Hunting is a loophole in the 2nd Amendment to the Bill of Rights.

There is no privilege to keep and bear arms.

Arms are for killing people. All other uses of an arm are illegitimate uses.

Know your rights. When stopped by police and not doing anything wrong, tell them you don't consent to searches. They are allowed to lie to you, but you're not allowed to lie to them. Just say nothing.
Reply With Quote
  #3  
Old 11-15-2012, 12:31 PM
savagemann's Avatar
savagemann savagemann is online now
Member
 
Join Date: Jul 2012
Posts: 258
iTrader: 5 / 100%
Default

I usually knock em off with the tip of an aluminum cleaning rod....although I have been told to just shoot them out.

Sent from my SCH-I510 using Tapatalk 2
Reply With Quote
  #4  
Old 11-15-2012, 3:17 PM
nicoroshi's Avatar
nicoroshi nicoroshi is offline
www.Buildyourownak.info
CGN Contributor - Lifetime
 
Join Date: Jan 2009
Location: Da East Bay Bro!
Posts: 3,697
iTrader: 23 / 100%
Default

I run a bore snake back and forth through the barrel after I drill a gas port hole.
The brush on it will normally take anything that might be an issue off.
If it's really small, and the above doesn't get it I shoot it out.
Reply With Quote
  #5  
Old 11-15-2012, 3:26 PM
Dan FS71's Avatar
Dan FS71 Dan FS71 is offline
Member
 
Join Date: Jun 2009
Location: Orange County
Posts: 403
iTrader: 14 / 100%
Default

You can pull a bullet and push it down the bore and it should remove the burr. Likely the 1st shot will take it out too but this is alittle less agressive
Reply With Quote
  #6  
Old 11-15-2012, 5:45 PM
esqui2809 esqui2809 is offline
Member
 
Join Date: Apr 2009
Posts: 102
iTrader: 13 / 100%
Default

Thanks for the feedback. I tried the rod and the brush, still there ill try a bore snake then all three again if still no dice just have to send one down range. Thanks again
Reply With Quote
  #7  
Old 11-18-2012, 7:39 PM
esqui2809 esqui2809 is offline
Member
 
Join Date: Apr 2009
Posts: 102
iTrader: 13 / 100%
Default

Went shooting today gun ran like a champ ended up just putting one down range. No issues
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 1:08 PM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2016, Calguns.net an Incorporated Company All Rights Reserved.