Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > INTERESTS AND ACTIVITIES > Ammo and Reloading
Register FAQ Members List Calendar Mark Forums Read

Ammo and Reloading Factory Ammunition, Reloading, Components, Load Data and more.

Reply
 
Thread Tools Display Modes
  #1  
Old 11-29-2012, 10:13 AM
Press Check Press Check is offline
1911 Aficionado
CGN Contributor
 
Join Date: Jun 2011
Location: BLM
Posts: 4,584
iTrader: 58 / 100%
Default Thumlers Model B

Hey, is anyone having a problem with their tumbler leaking a bit of water while processing brass?

I think I might be overtightening the wingnuts and causing creases in the plate, but I'm not sure, and just wanted to get some insight.
Reply With Quote
  #2  
Old 11-29-2012, 7:38 PM
Revoman Revoman is offline
Senior Member
 
Join Date: Dec 2007
Location: San Diego/Lakeside
Posts: 1,539
iTrader: 6 / 100%
Default

I am having zero leakage in my tumbler, I tighten very snugly, but only by hand with the wing nuts as supplied.

Are you sure that there are no pins between the top and barrel, no other debris? I usually wash my rubber lid part down and store it by itself on a flat surface with the metal lid on top to keep the rubber flat.
Reply With Quote
  #3  
Old 12-01-2012, 3:11 PM
stilly stilly is offline
Banned
 
Join Date: Jul 2009
Location: Currently in a shanty I made in the river bottom by Eastvale.
Posts: 9,004
iTrader: 44 / 100%
Default

If you have water on the top it will leak out a tad, if you have water that fell down the outside you will notice some leakage. If you have pins stuck between the top and barrel gasket you will see some leakage.

IF all of your water is leaking out then you have issues with either not tightening it properly or something else. If it leaks just a tad then I find it acceptable. Usually though it is just residual water that got caught down below in that lower channel that falls out I think.

ALSO, when I tighten it shut, I do it like a lug nut pattern or manifold pattern, I will do one nut down to almost tight, then go across the way and do another one, then another and so on each time doing one across the way. Finally I will go over them again in a similar pattern and tighten them all down so that way they all get about the same amount of torque. I have washed prolly 100+ lbs of brass through it and usually any water that looks like it is leaking is my fault. Worst case get some fender washers to put under the nuts... I think any water I have seen was really residual water and maybe only a tablespoon or two at most. Is yours brand spanking new? Maybe it needs to get broken in.

Last edited by stilly; 12-01-2012 at 3:13 PM..
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 5:02 AM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2016, Calguns.net an Incorporated Company All Rights Reserved.