Late january 80% Milling group times available next week - San Diego 1/29 & 1/31

[C4Charlie]

Hello all,

I am organizing a milling party schedule for doing 80% AR15 lowers in Miramar (at Intuitive Designs) for next Tuesday and Thursday afternoons. The prices are as follows: $60 for the first lower and $55 for each lower thereafter (milled the same day). *** PLEASE NOTE CORRECTED ENGRAVING PRICING: Engraving is offered starting at $35, but will need to be scheduled for a different day as these milling days are far to busy to try and squeeze in engraving time. The engraving pricing schedule is as follows: $35-$40 per side for text only engraving (depends on how much text is to be engraved). Custom logo engraving is also available starting at $40 and up per logo. *** The engraving process actually takes longer than the completion of the 80% lowers due to the additional programming time and slow cutting time.

The time required for each lower is 20 minutes, therefore we are making these appoinments in 20 minute blocks. Therefore, if you have 5 lowers to do, you need to reserve a 1:40 minute block to get them all done. The scheduling is being pre-set so that we don't have guys just standing around all afternoon waiting in line. If you miss your appointment time, we will give your spot to the next person in line. This will keep things moving for everyone.

*** Important note: Due to the recent events in Connecticut we will need a photo copy of your drivers license. This will not be given to anyone or used for anything but Jimi's personal files. There is an old saying "CYA" and he's just covering his *****. You must be legal to possess a firearm in the state of California. Here is the link to check for yourself. http://oag.ca.gov/sites/all/files/pd...ms/pfecapp.pdf This is for your information because ignorance is not an excuse is the eyes of the law.

The scheduling for next week will be for Tuesday and Thursday afternoons from 1PM with the last paperweight going onto the mill no later than 5:20. That gives everyone time to finished up and out the door by 6 pm.

Appointments are now Open for Tuesday 1/29/13 and 1/31/13. Please look at the available times and send me your start time and how many time slots you need to machine your lowers. I will be posting updates every few hours. If you have special requirements, please PM me so that I can see if they can be accommodated.

Tuesday:
1:00 - jdrhds14 1 of 2
1:20 - jdrhds14 2 of 2
1:40
2:00
2:20
2:40 - Kiowa 782 1 pc
3:00
3:20
3:40
4:00
4:20 - Frgman251
4:40 - Elwood 1 of 2
5:00 - Elwood 2 of 2
5:20 - Jimi appt.

Thursday 1/31/13

1:00 - MFortie 1 of 2 AR15
1:20 - MFortie 2 of 2 AR10
1:40
2:00 - Grvv 1 piece + engraving (future date p/u)
2:20 - Bobtart 1 of 2
2:40 - Bobtart 2 of 2 (possible engraving)
3:00 - Bobtart engraving (tentative)
3:20
3:40
4:00
4:20
4:40
5:00 -sac42705 1 of 2
5:20 -sac42705 2 of 2

I hope to see lots of you there!

C4 Charlie

[postalpredator]

Do you have any 80% lowers for sale on site ,or is it a bring your own lower event

[C4Charlie]

Currently this is a BYO lower event. Both Jimi and I have lowers on order that have been on backorder for a while.

[grvv]

I will take 2:00 pm on the 31st, I have one lower paper weight, and engraving when you do that.
Greg

[MFortie]

I'd like the 1:00PM slot on the 31st please.

Thanks.

Edit: 1 lower

[C4Charlie]

Grvv and MFortie, you guys are confirmed. He schedule has been blocked off for you. Please try to arrive about 30 minutes early to allow time to check in, ask questions and get set up.

Please PM me if you need any assistance in the meantime. Have a great weekend!

C4Charlie

[AsianAnts]

Charlie, thanks for putting this together.. im going to see my friend today.. i'll post shortly after i get updates.

[Frgman251]

Charlie, I'm new here on Calguns and purchased a paperweight recently. I am out of state military with a New Mexico DL. I have purchased a firearm here in California before. If it is not an issue can you put me down for 5:20 on Tuesday please?

[C4Charlie]

You are in sir, but just reserved through the end of the day on the 29th. Thanks for asking first. I will get the schedule updated now. Can you come in at 4:20?

C4

[sac42705]

I would like to take 5 and 520 on the 31st. I have 2 80% lowers.

[C4Charlie]

Confirmed sac42705 for two pieces.

[sac42705]

Thanks

[jdrhds14]

Charlie could you please put me down for 1:00 pm and 1:20 pm on Tuesday? I have 2 lowers. I'll be PM-ing you soon as well.

[Frgman251]

Charlie, forgot to ask, where is his shop located?

[BucDan]

I don't have any 80%, but how often will you be doing this?

[C4Charlie]

Originally Posted by Frgman251

Charlie, forgot to ask, where is his shop located?

Jimi's shop is at 9219 Mira Este Ct., San Diego, CA. It is inside the Loose Cannon Customs facility. please tell the nice lady at the front counter that you have an appointment with Intuit Designs.

I can PM directions to anyone who needs them.

Originally Posted by BucDan

I don't have any 80%, but how often will you be doing this?

No worries sir. Just let me know when yours comes in, we will get you scheduled. I was able to buy one on Friday, but I payed top dollar for it. I figured someone might need one for our group. I paid $210 plus tax from a shop in Temecula. It should be in on Monday. If anyone wants it, I will supply it with my purchase receipt when you come in for milling. Please PM me with requests. Again, I will only have the one in. The rest of mine are on back order.

[bongfoo]

damn! wish i had a 80% right now.. can't find one locally for the life of me...

[Kiowa782]

I would like1/29/13 at 2:40 with 1qty 80% lower.

Thanks

[C4Charlie]

Kiowa782 you are confirmed for 2:40 on 1-29-13.

Bongfoo - PM coming your way

[Frgman251]

Originally Posted by C4Charlie

Mimi's shop is at 9219 Mira Este Ct., San Diego, CA. It is inside the Loose Cannon Customs facility. please tell the nice lady at the front counter that you have an appointment with Intuit Designs.

I can PM directions to anyone who needs them.





No worries sir. Just let me know when yours comes in, we will get you scheduled. I was able to buy one on Friday, but I payed top dollar for it. I figured someone might need one for our group. I paid $210 plus tax from a shop in Temecula. It should be in on Monday. If anyone wants it, I will supply it with my purchase receipt when you come in for milling. Please PM me with requests. Again, I will only have the one in. The rest of mine are on back order.

Charlie, thanks for the info. Just to confirm, I am still good for 5:20? Or would he prefer I try to make it for 4:20?

[C4Charlie]

4:20 if at all possible, please.

Thanks for checking in.(got ur spot held)

[Frgman251]

Originally Posted by C4Charlie

4:20 if at all possible, please.

Thanks for checking in.(got ur spot held)

I will definitely try my best to make it.

[C4Charlie]

Thanks Frgman251.

Ok guys, we will be seeing the first of you today.

Just a reminder, here is the schedule for this afternoon so far:

1:00 - jdrhds14 1 of 2
1:20 - jdrhds14 2 of 2
1:40
2:00
2:20
2:40 - Kiowa 782 1 pc
3:00
3:20
3:40
4:00
4:20 - Frgman251
4:40 - Elwood 1 of 2
5:00 - Elwood 2 of 2
5:20 - Jimi appt.

Please let me know if you need want to get on the schedule for this afternoon.

Have a great day.

[radennis]

Can you do Billet lowers from Quinten Defense?

[C4Charlie]

Absolutely sir.

Please let me know if you would like to come by today. We still have time.

Charlie

[MFortie]

Charlie -- thanks for coordinating this party. I machined my two this afternoon and everything went smoothly.

Looks like Jimi got the .22LR to you, based on the post you left on Cobralc's thread...

Glad I could help!

Now when all the pricing and panic buying settles down, I can finish my .308!