Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > INTERESTS AND ACTIVITIES > Ammo and Reloading
Register FAQ Members List Calendar Mark Forums Read

Ammo and Reloading Factory Ammunition, Reloading, Components, Load Data and more.

Reply
 
Thread Tools Display Modes
  #81  
Old 06-08-2017, 12:46 PM
Masterdebater's Avatar
Masterdebater Masterdebater is offline
Senior Member
 
Join Date: Aug 2009
Location: Lancaster/antelope valley
Posts: 1,093
iTrader: 7 / 100%
Default

Negative but I am also someone who likes big booms and heavy recoils. They're fun!
Reply With Quote
  #82  
Old 06-26-2017, 10:52 AM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Guys asking about strong economical bolt gun to use for 28ga and
410 ga and 32ga with brass cases and higher pressures than plastic cases.
They can use a MN bolt action, here is pic of one with
our 585 case in the action.Guys can get Magtech brass cases or have
RMC make them....Guys can make 32ga case from 500 NE,
410s from 9.3 x 74 brass, etc..



Here is picture of our 416 HSM case sectioned next to original
BMG case on the right sectioned, to show that we still have
enough thickness in the sides to handle high pressure,
in a case with 310 gr capacity..We are getting the wildcatting
work set up so we can do at least hundred a month.
We have lots of 585s, 375HEs, 416 HEs, 408 HEs.....
And working toward getting 416 HSMs in big numbers.



Here's comparison of 416 target cases, 1st 416 HE, have whole bunch.
Second is model of what I'd have made on medium machine, if I could,
the 416 HE Long. It has capacity of 230gr..
Third is our 416 HSM which we are working on making by wildcatting bmg
cases, And if had run long cases, make longer 375 HE necking down 416 ..




Bryan Litz just recently shot 3 shot group at 2 miles using Paul
Phillips heavy barreled, target rifle built by Lethal Precision in
375 Lethal Mag(585HE necked down, very similiar to 375HE )...
It grouped 17.5 inches tall by 22 inches wide.

Applied Ballistics shooter Mitch Fitzpatrick just hit 3 of 5 at 3520 yards,
weekend 10-13th at Valdina Ranch , west of San Antonio.
Also used the 375 LM case similar to our 375 HE
Great shooting at the 2017 World's Longest Shot Challenge. Ed
Reply With Quote
  #83  
Old 07-23-2017, 3:30 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

The 12ga FH case now is in the new COTW book on
last page in the wildcat section, I think page 324.
They gave good credit to Rob for the idea of that case....


The model 416 HE long case in middle, hydro formed one,

has case capacity of 240 gr, and the 416 HSM in picture,

on the right, we fired a case twice, capacity is 320gr.. Ed..




More info out now; short, fat cases sticking, pockets not lasting as expected.
Trying to get best speeds the things raising pressures are bad case
proportions, too sharp of shoulders, too fast of powders...........
and debth of the bullet into the powder space, as shown in the picture below..
My 375, 416, etc testing, bullets loaded like bottom one, in longer freebore....Ed.

Reply With Quote
  #84  
Old 09-04-2017, 1:54 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is case measurements for our 416 HE target case
made from our 585 HE big belted case. Ed




Here is picture of 375 HE left, 416 HE next, 416 HSM right..




Here, tentative specs, 416 HSM case we are doing from bmg brass,





A 375 HE, with Lawton action, few are being done with those .....

Reply With Quote
  #85  
Old 10-09-2017, 2:04 AM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

A 585 HE ...shot with moderate heavy load......

https://scontent.cdninstagram.com/t5...09533184_n.mp4


Here is a 375 HE target gun set up, by Asteroid Precision...




Here is video of it being tested... And with a 350gr bullet about 3450-3475,

bolt opened easily with one finger...And he's just getting started

and is checking on better powder, Ed..



https://www.facebook.com/AsteroidPre...location=group
Reply With Quote
  #86  
Old 11-10-2017, 7:32 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is recap simple setup to get faster loads with 12ga sabots

& slugs, Example using break actions...., reaming chamber

in a 12ga break action to 3.5" with a 3.5" 12ga reamer, that isn't

something needing special order, and use 3.5" plastic cases , or

get 3.5" brass cases made. With mag shotgun primers and

our slower powder loads you can get a quarter more speed,

which gives 50% more energy...


585 Hubel Express video, 190ft/lbs recoil, heavy load, gun little light.....

https://www.youtube.com/watch?v=tyS9zZ8ElJA


Another view of Asteroid Precision's.... 375 HE target gun,




Here is our 416 HSM we are developing next to 416 Barrett, Ed

Reply With Quote
  #87  
Old 01-11-2018, 5:24 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here in picture of the cases, are shown the steps in making

our 416 HSM case, from BMG brass,, Ed




We might have a company that is doing a bolt gun with an action

between BMG size and longer rifle actions used for 375 HE,

375 Lethal, and Cheytacs.. To use for our 416 HSM without

having to do extreme rebating of the rim.


Here is picture of 620 416 hsm cases half done. Done on cnc ,

that slimmed them down, cut new rim and extractor groove.

There are over 500 more at cnc getting done now, plus we have

1000s more bmg cases we make them from, when needed..

This case is public domain and if anyone wants to make

them we can give the steps involved...Ed.

Reply With Quote
  #88  
Old 02-12-2018, 7:15 AM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

For big long cases our testing is showing that the 416 easier to get powders to work with, less problems ..
Maybe building a target gun,don't have 375 barrel all ready, maybe go 416....

We got cases, 416 HE and 416 HSM, as well as 375...
CEB and others will have bullets...CEB will be doing .416 in 450gr, 475gr, 500gr, 525gr and 550gr

Got sent 5 thick sided sample cases, same OD base as 585/375.416 cases, same belt, just .180" longer,
did a 416 HE, chambered extra barrel , cases stick over 50k. They have about .042" total taper, .021" per
side, when I necked couple to 416. That is a lot of taper , twice the taper of my 416HE...hanging up at 50k..

I could maybe go to 65k with these if we made taper with ..012" - .016" more taper to each side, but that is
no way to build target cases. I'd have to crunch down case shoulder diameter. And would look like 30-30.

And crazy part is, the case has enough brass material to thin up sides and stretch them way out to 4 or
more inches,, They weigh 150 gr more than our 585/375/416,, but with real thick sides they actually
hold less than our 416 HE with thin sides, that is .180" shorter...Our case does 65k ok without sticking..

And we can make super long 4" cases work if we had means to get them built, as we have
15 powders slower than HBMG.Here is pic of thin and thick sided cases, sectioned for comparison.Ed..


Reply With Quote
  #89  
Old 03-04-2018, 8:13 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is a drawing depicting the layout of thick and thin sided cases,
like my 585/375/416 HE thin sided ones and the thick one in picture.

And my 585 case is not perfect, as where it transitions from the
heavier corner to the side it isn't gradual, so case separates there
shortening case life. There are others made that way including brand X.
The dotted line is what it should be............



Others have sent cases to section and look at, that are built thick sided and they
stick also for the folks, If a longer case with about 5 sq in of side surface sticks and
don't spring back, the coefficient of friction is about .01 then the pull needed to move
it is 2500-3500 lbs..That is for big cases with normal amount of slant to the sides.

Here is picture of six nyati and gibbs size cases sectioned.. the5th one is present 585 HE
and 6th is thick sided version. 1st 600 OK which essentially nyati basic case left straight, belt added



In the picture the nyati gma is one we built most of our first 585s on. Before we had factory run.
Reworking made it in size that is my 585 HE, but that brass had the sides of perfect thickness,
not too thick, but thin without sharp transition my new factory 585s had, they last forever as 585s......

Fourth one is an older nyati case I used to make about 10 of my 585s from,had thin sides, heavy corner
and sharp transition from the corner, tested 20 years ago, and they would separate after 4-6 hot loads
as 585s, my factory 585 with right powders, as a 585 will get 10 hot loads, and necked down to
416/375 4- 6 hot loads, right powders used, Moderate 577 equivalent, factory 585 at least 20 loads..Ed.
Reply With Quote
  #90  
Old 03-21-2018, 2:56 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Guy sent thick sided 375 case, next size base diameter up from Nyati.He said,
'Yes I ran them in a ___________ rifle built by ____, the best I
could get was 44000 psi, any more and they were stuck''

Big bore guys. other forums over the years related that trex/african case in 585
size, thick sided cases, stuck when they loaded them over 45k psi.

Another just sent us, thick sided 375, long case, same base OD as our 585 HE,
416 HE, 375 HE, and Mitch's 375 Lethal, and the thick ones stuck over 45k psi.

Now you can fill those cases up, with ultra slow enough powder so they won't
stick, but powder is too slow for max speed. Might get a little more
speed, with thick sides case, but case got to be 4- 4.5 inches long..

. Anyone needing a sectioned case of the ones I made the first of my 585s from,
contact me, if they want to get a general idea of what case side thickness should
be, in Gibbs size cases on up to about trex and 375 VM size case diameter.

Here is pic of our 585 based case next to brand X and thick ones, both have
same sharp, thinner, corner, where transition from heavy angled corner, to the
side, the carbide draw rod could easily be reshaped with diamond wheel,
just by grinding off sharp transition corner. Then sides would be perfect.., .




Here is picture of 416 HE in a Choate target/varmint stock guy is doing,
using long action BSA U9 action.Setting in stock ready to do bedding..Ed

Reply With Quote
  #91  
Old 04-20-2018, 7:03 AM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is picture of thick 375 case sent to me, with thick sided trex case, and our HE case,
The thick 375 case is .050" bigger OD base, but inside is no bigger than HE cases..
These thick sided 375s stuck for the guy using them, when loaded over 44,000 psi....



Got guys asking and doing it, to do 416 HSM case for BMG actions, so leaving rim same,
as the original bmg rim, so will neck them, fire form to the longer shoulder, like the others.
Base a little bigger, Shoulder same diameter, same 30 degree slant, neck will be same..

Inside of case still has close to same shape, volumne within 3 % as ones we slimmed down more.
Some want to use bmg actions and can't wait for intermediate actions, or already have bmg action.
And they are really getting interested in the complete line of 416 CEB bullets now being done
clear up to 550 gr...

So there will be 3 versions, one for actions .750" bolt, one for .800-.850" bolt,
And one for bigger bmg bolts. The ones for BMG called 416 HSM2 ..

Here is 416 HSM guy working in a Montana PH, in a heavy thumbhole target stock. Ed


Reply With Quote
  #92  
Old 05-10-2018, 7:12 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is sectioned 585 HE case in the middle, we first made from

another case, years ago before we had factory run of brass and

it had perfect thickness on the sides and inside corrner.

We could fire them many times without sides thinning..

First case is factory run of our 585 HE, 3rd is case that is too

thick of sides and sticks at high pressures..



Pic of our factory run cases necked down to 375 and fired 4 times

at high pressure on the right, with unfired case on the left.

Our case is not perfect but does work...Ed

Reply With Quote
  #93  
Old 07-09-2018, 4:39 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

About 416 cal bullets............

The heaviest 550 gr for Extreme ELR probably be best 8 to 1 twist , in 416 caliber bullet,
and 520 gr 9.5 to 1, and 470gr 10 to one, Some barrels I picked up are 10 to 1.......

Now a novel idea is to lighten rear of bullet with small shallow hole drilled in base, might do better
long range.which would allow 10 to one barrel stabilize the heavier 550 gr bullets for ELR.
Making bullet nose heavier makes it more stable in flight, needing less spin,
like our hollow base 585 cal minie bullets only need 48 to 1 twist, or less
while out regular 585 bullets need about 24 to 1 to stabilise them..............

The winner of the King Of 2 Mile shoot last week was using 416 Barrett with a 1 to 10
twist, with a 500 gr CEB Lazer bullet, ...Robert Brantley, with Manners Stocks....

Paul Philips was third with a 416...

GOOD NEWS-- There is now an importer and seller of our 585 HE brass getting set up here,
in US, hopefully will be in stock, few weeks........ http://bertrambrass.com .. .. Caleb Hallet..

Have got another intermediate size action besides the Montana PH our guys working on,
to do speed testingwith. It is big long REM style action that can take our 416 HSM, ED
Reply With Quote
  #94  
Old 07-09-2018, 9:17 PM
Dark Hunt's Avatar
Dark Hunt Dark Hunt is offline
Member
 
Join Date: Sep 2016
Posts: 420
iTrader: 0 / 0%
Default

You'd have to have porters to carry the big bores and an orthopedic surgeon to take care of you after you shoot it.

The small bores look like they would work for the serious long range shooters.

What's the case capacity of the 416 HSM and what powders would you be using?
__________________
NRA Endowment Life Member

Last edited by Dark Hunt; 07-09-2018 at 9:20 PM..
Reply With Quote
  #95  
Old 07-24-2018, 7:27 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Cap is 320 gr, use the slow surplus powders llike

20n29, WC 880 to 886..and othera we are testing.

Experimental intermediate size action with the Montana PH, for comparison.

It is an experimental action for our 416 HSM, to do our speed testing with

and get a better action than Cheytac size actions, for bigger case ELR use,

without going all way up to more expensive, huge actions.

It is big long round style action that can take our 416 HSM, almost

1.6" diameter action and .800" bolt, with locking lugs nearly as big as most BMG actions.... ED


Reply With Quote
  #96  
Old 09-18-2018, 11:41 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is picture of the bolt from the experimental action,

with our 416 HSM case in it. Note the amount of the

base size of locking lugs, the amount of area on the bolt..





Here is link to guy doing special 585 HE in the EU,

Good pictures............www.585he.cz

We tested intermediate action with a 700HE barrel we had here.

Just temporary to test strength. 1000 gr over 3100..

Action worked fine.. Ed.
Reply With Quote
  #97  
Old 10-20-2018, 2:50 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

Here is video of early water barrel test of the

12ga From Hell, from years ago.

https://www.youtube.com/watch?v=c48zTpsgbuk


Here is picture from that video..





Here is the intermediate size action for 416 HSM with test barrel, .Ed

Reply With Quote
  #98  
Old 12-05-2018, 10:39 PM
hubel458 hubel458 is offline
Member
 
Join Date: Sep 2006
Posts: 499
iTrader: 0 / 0%
Default

In 416 HSM got a 415 gr long target bullet 3800,

with plain barrel, no brake, on intermediate action,

Our 416 HE gets same 415gr bullet to 3300.Ed
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 5:40 AM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2018, Calguns.net an Incorporated Company All Rights Reserved.
Calguns.net and The Calguns Foundation have no affiliation and are in no way related to each other.
All opinions, statements and remarks made by Calguns.net on this web site and elsewhere are solely attributable to Calguns.net.