Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > FIREARMS DISCUSSIONS > Rimfire Firearms > Rimfire Gallery
Register FAQ Members List Calendar Mark Forums Read

Rimfire Gallery Post pictures of your rimfire rifles and handguns here!

Reply
 
Thread Tools Display Modes
  #1  
Old 04-23-2011, 8:58 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default Razor 80% 10/22 build

Decided to try building one of these even though I had no access to a mill. I do have a drill press, so I figured what the heck. No DROS, no ten day wait, or any other California legal crap to contend with. To tell the truth, everything went fairly well, but the barrel hole definitely introduced a major pucker factor. I checked and double checked and when finally confident all was aligned properly, I step drilled the barrel hole. I started with a 1/4", then 3/8", then 1/2", then 9/16", 5/8" and did the final drilling with a 21/32" drill. I then used a 11/16" hand reamer for the finished hole. All in all, quite satisfied with the build. Test fired it at the Reed's indoor range. Not quite a good benchrest available there, but standing with the bipod on the bench I did get off some decent grouping.
Rudy








Reply With Quote
  #2  
Old 04-23-2011, 9:00 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

Oh yeah, that's a ten shot goup at 25 yards....
Rudy
Reply With Quote
  #3  
Old 04-23-2011, 9:02 AM
TacDriver5five6 TacDriver5five6 is offline
Member
 
Join Date: Jan 2011
Posts: 152
iTrader: 2 / 67%
Default

nice job...
__________________
WTS:

Reply With Quote
  #4  
Old 04-23-2011, 9:04 AM
gatesbox's Avatar
gatesbox gatesbox is offline
Senior Member
 
Join Date: Oct 2010
Location: San Carlos, CA
Posts: 1,862
iTrader: 15 / 100%
Default

Nice, I was curious about these....what was your cost without the optic? I like the integrated rail on the razors.
__________________
"Cum catapultae proscriptae erunt tum soli proscripti catapultas habebunt."
Reply With Quote
  #5  
Old 04-23-2011, 9:45 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

Thanks guys. I probably have a little under $500 invested in this not including some of the tools I had to buy such as drill bits and drilling jig and reamer.
Rudy
Reply With Quote
  #6  
Old 04-23-2011, 7:11 PM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

Here are the specifics:

Select Fire 80% RAZOR Receiver with Extended Rail (aluminum finish)
Select Fire Modified Black Bolt Assembly 10/22
R25P Bolt Buffer
Select Fire 1022 Stainless Charging Handle and Spring assembly
Volquartsen® TG2000 10/22LR Trigger Guard and Assembly
Adjustable Barrel V-Block Kit
Green Mountain 20" SS Bull Barrel .920 outside diameter
Stainless Steel Stock Take-Down Screw
Fajen basic composite stock
Weaver Quad Lock Rings 1" Med Height (Silver)
Vintage Tasco 4 X 40 rifle scope (Made in Japan)
Harris Bipod

Rudy
Reply With Quote
  #7  
Old 04-30-2011, 3:06 PM
Justintoxicated's Avatar
Justintoxicated Justintoxicated is offline
Veteran Member
 
Join Date: Mar 2009
Location: Escondido
Posts: 3,780
iTrader: 12 / 100%
Default

So it's just drilling holes? I have been looking for something to use this cross sliding vice for...

I dunno, I hardly ever even shoot my 22 anymore. But I think this sounds ALOT easier than an AR 80%?

looks great man.

Last edited by Justintoxicated; 04-30-2011 at 3:14 PM..
Reply With Quote
  #8  
Old 05-04-2011, 11:49 PM
MrPlink's Avatar
MrPlink MrPlink is offline
I need a LIFE!!
 
Join Date: Mar 2010
Location: Portland / East Bay
Posts: 12,537
iTrader: 8 / 100%
Default

Quote:
Originally Posted by Justintoxicated View Post
So it's just drilling holes? I have been looking for something to use this cross sliding vice for...

I dunno, I hardly ever even shoot my 22 anymore. But I think this sounds ALOT easier than an AR 80%?

looks great man.
have you milled an AR receiver?
You could call that "just drilling holes" too.

Its the same process, you can "mill out" an AR receiver with just a drill press too. My buddy did just that not too long ago. PITA though.
__________________
The California Moderate Centrist Militia member in exile

disclaimer:
everything I post is for arguendo and entertainment purposes only, and should not be construed to be legal advice
Reply With Quote
  #9  
Old 05-06-2011, 12:07 PM
hypnoman's Avatar
hypnoman hypnoman is offline
Senior Member
 
Join Date: Feb 2010
Posts: 1,073
iTrader: 73 / 100%
Default

Great build, Rudy!!

I've been looking into this and appreciate your inspiration, man! Great job!
Reply With Quote
  #10  
Old 05-06-2011, 12:15 PM
semperfidelis354's Avatar
semperfidelis354 semperfidelis354 is offline
Member
 
Join Date: Dec 2010
Posts: 437
iTrader: 2 / 100%
Default

Very nice job! This is a project on my "why the he'll not" list. Hopefully I get to it one day
Reply With Quote
  #11  
Old 05-06-2011, 5:07 PM
Dead*Reckoned Dead*Reckoned is offline
Veteran Member
 
Join Date: May 2010
Posts: 2,641
iTrader: 13 / 100%
Default

Nice job! I'm loving the stainless look, did you use a clear coat finish?
Reply With Quote
  #12  
Old 05-13-2011, 6:46 PM
Lostsheep's Avatar
Lostsheep Lostsheep is offline
Senior Member
 
Join Date: Aug 2010
Location: 8mi SSE of Drawbridge Ca
Posts: 909
iTrader: 22 / 100%
Default

Looks good. I started to finish mine today. Was your lower really rough? I ask because mine looked like it was deburred by an amateur.
Reply With Quote
  #13  
Old 05-19-2011, 8:51 PM
para-frame para-frame is offline
Junior Member
 
Join Date: Jul 2007
Posts: 54
iTrader: 0 / 0%
Default

I need to look in to this, I have been wanting a charger but finding an out of state FFL that will install a fixed single shot sled for less then $75 bucks is teeing me off. I could legally build up a charger like pistol with a fixed mag for less then the cost of a charger much less the added cost of the transfer and fixing single shot mag.
Reply With Quote
  #14  
Old 05-21-2011, 10:09 AM
Rebel Warrior's Avatar
Rebel Warrior Rebel Warrior is offline
Junior Member
 
Join Date: Aug 2010
Posts: 40
iTrader: 0 / 0%
Default

That thing looks freakin awesome
Reply With Quote
  #15  
Old 06-14-2011, 9:29 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

Quote:
Originally Posted by Dead*Reckoned View Post
Nice job! I'm loving the stainless look, did you use a clear coat finish?
I haven't added any finish to the receiver. It looked good the way it came, and I didn't add any scratches to the receiver during the build. If at a later time the finish starts to deteriorate, I'll re polish it and maybe put on some clear coat of some type.
__________________
Reply With Quote
  #16  
Old 06-14-2011, 9:30 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

Quote:
Originally Posted by Lostsheep View Post
Looks good. I started to finish mine today. Was your lower really rough? I ask because mine looked like it was deburred by an amateur.
No, actually the finish was very good on mine. Did you get your receiver from Select Fire?
__________________
Reply With Quote
  #17  
Old 06-15-2011, 6:34 AM
rudynix's Avatar
rudynix rudynix is offline
Member
 
Join Date: Apr 2011
Location: Hollister, CA
Posts: 225
iTrader: 2 / 100%
Default

I had ordered a Revolution Tundra stock for the Razor 1022 when I was building it two and a half months ago. Well, it arrived a couple of days ago so I went ahead and swapped stocks.

__________________
Reply With Quote
  #18  
Old 06-15-2011, 8:29 AM
Lostsheep's Avatar
Lostsheep Lostsheep is offline
Senior Member
 
Join Date: Aug 2010
Location: 8mi SSE of Drawbridge Ca
Posts: 909
iTrader: 22 / 100%
Default

Quote:
Originally Posted by rudynix View Post
No, actually the finish was very good on mine. Did you get your receiver from Select Fire?
Yeah, I got it from select fire. There were many surfaces on mine where the machining didn't blend surfaces the way I liked so I spent a good amount of time filing. Overall I am very happy with it but the bad blends and large burrs were a bit frustrating.
Reply With Quote
  #19  
Old 07-14-2011, 3:19 AM
straykiller's Avatar
straykiller straykiller is offline
Veteran Member
 
Join Date: Feb 2010
Location: Fresno area
Posts: 2,575
iTrader: 14 / 100%
Default

how complicated was it to complete the receiver?
__________________


Zombie Stickers For Sale

ClassifiedWeapons.com

Looking for a particular parts kit? Check out our parts kit locator that is automatically updated every 6 hours. Now you can see parts kits being offered by multiple websites in one location. Just select the parts kit button on the right of the home page to begin looking.
-------
Home Builds- 1919a4, Sten Mk3, Romy G Ak-47, PSL Pistol,Romanian RPK
Reply With Quote
  #20  
Old 07-14-2011, 6:49 AM
psssniper's Avatar
psssniper psssniper is offline
nulla lex prohibet
CGN Contributor
 
Join Date: Oct 2005
Location: San Clemente
Posts: 2,846
iTrader: 193 / 100%
Blog Entries: 3
Default

Quote:
Yeah, I got it from select fire. There were many surfaces on mine where the machining didn't blend surfaces the way I liked
Mine too. It was bad enough that I contacted the company and they basically told me to eff off
__________________
"I do not love the bright sword for its sharpness, nor the arrow for its swiftness; I love only that which they defend.
victus exaro somniculosus, somnus exaro ieiunium
Reply With Quote
  #21  
Old 07-14-2011, 8:51 AM
Lostsheep's Avatar
Lostsheep Lostsheep is offline
Senior Member
 
Join Date: Aug 2010
Location: 8mi SSE of Drawbridge Ca
Posts: 909
iTrader: 22 / 100%
Default

Quote:
Originally Posted by straykiller View Post
how complicated was it to complete the receiver?
It is all hole drilling operations unlike an AR lower. I would say that everything is doable with a drill press and a jig except for the barrel hole. You really need a the rigidity of a mill and something to cut the hole accurately. How many people have a boring head or a .6875" reamer laying around?

Reply With Quote
  #22  
Old 08-01-2011, 8:19 AM
Vanilla Gorilla's Avatar
Vanilla Gorilla Vanilla Gorilla is offline
I need a LIFE!!
 
Join Date: Aug 2010
Posts: 10,922
iTrader: 39 / 100%
Default

Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 12:09 PM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2018, Calguns.net an Incorporated Company All Rights Reserved.
Calguns.net and The Calguns Foundation have no affiliation and are in no way related to each other.
All opinions, statements and remarks made by Calguns.net on this web site and elsewhere are solely attributable to Calguns.net.