all sold or withdrawn

[anothergunnut]

[b]Make: Roggio, ATI, DSA,

[b]Model:AR15, FAL,

[b]Caliber:223, multi cal, 308,

[b]Location (city or county): Modesto

[b]Price: 250, 350, 950,

[b]Will ship (Y/N): Will ship lowers but not the P220 or FAL

Stripped AR15 lowers for sale but still interested in trades for the guns listed below. I have a couple AR15 lowers that are forged, mil-spec lowers. Roggio that is a "multi-cal" and ATI that is 5.56. The Roggio has a LPK and bullet button installed. The AR15 lowers are $250 or $350 with the LPK and bullet button. I will ship the lowers. Photos for the lowers are below and are #004, 005, and 006.

I also have a Tactical Machine AR-10 (I know, it's a DPMS pattern) lower that is stripped for $400 (This is SPF)

1/1/13 addition: I have another Tactical Machine AR-10 lower that is used and has a LPK installed. It includes the proper front and rear pivot pins and bolt catch; these parts are about $30 in addition to a standard LPK. This is a USED receiver and has some cosmetic damage. There is wear on the anodizing at the top of where the receiver extension amounts, some wear on the front of the receiver where it pivots and a minor nick or two. It's not a perfect, virgin receiver but it is still pretty nice. See photos. Asking $400. This is SPF.



Trying to make room in the safe by selling some of my less used guns. Will do face to face in the Modesto area North to Stockton, South to Turlock, West to Manteca, and East to Oakdale. I'm not really looking for trades but would consider the following in excellent or better condition. S&W double action revolver including models 15, 25, 27, 63, 67, Colt double action revolvers including Trooper Mk III in 22 or 357, Diamondback, Kahr PM9 or CM9 (no other models or calibers) CZ 75 SA or SP01 in 9mm (no other models or calibers) Ruger Mk2 pistols, Dan Wesson 1911. I'm not much of a photographer; all of the guns look much better in person.

[anothergunnut]

Next is a metric FAL. This was built on a DSA receiver utilizing an excellent condition, refinished kit. This has a magazine release lever that has a set screw to prevent it from releasing. Loading is from the top through a picatinny stripper clip dust cover. It has a thread protector rather than a flash hider as I was planning on eventually going featureless with this rifle. It can easily be converted to a detachable magazine by replacing the magazine release lever and spring. Comes with a ten round magazine. This rifle functions perfectly; I only shot it rarely, much less than 500 rounds. Asking $950 firm.

[anothergunnut]

Attachment 177586

Attachment 177587

Attachment 177588

Attachment 177589Finally, a Sig P220. This is a Sig CPO (certified pre-owned) that I purchased new (rebuilt). Sig goes through these guns and replaces everything that has any wear and then refinishes them. This is marked "Made in West Germany" on the slide. This is another gun I just don't shoot much (prefer my 1911) and has less than 1,000 rounds through it. Includes two factory magazines and the red Sig plastic case. Photos show greasy fingerprints; finish is near perfect. Asking $550 firm. This is sold.

[anothergunnut]

bump

[anothergunnut]

bump

[anothergunnut]

Now that President Obama has been re-elected; I may need to raise the prices to $50,000 due to the impending AWB! Buy now while they are still a bargain!

Seriously, these are all excellent, like new condition guns from top tier manufacturers. You won't be disappointed in any of these guns.

[Damn True]

Originally Posted by anothergunnut

[b]Make: PTR, DSA, SIG

[b]Model: 91KF, FAL, P220

[b]Caliber: 308, 308, 45ACP

[b]Location (city or county): Modesto

[b]Price: $950, 950, 550

[b]Will ship (Y/N): No


First up is a PTR-91 KF in .308. I purchased this new and I haven't shot it much; less than 500 rounds. It is in excellent condition with just a few small marks, mostly around the ejection port. Functions perfectly. Comes with an installed bullet button and a 10/20 magazine. Asking $950 firm.

Serial number is A6XXX. I have fired it with Indian (OFV) and Eastern European (Lithuanian?) and it has always fired and ejected perfectly. It leaves distinct flutes on the ejected brass.

What is the bolt gap on the PTR?


....and just out of curiosity is "metric FAL" a weapon that shoots AK ammo or one that shoots .308? Never heard that designation.

[anothergunnut]

Bolt gap is about .014 if I did it right.

FALs are either inch pattern or metric pattern all of which fire .308. FN exported worldwide with metric being the most common. Britain and a few others used inch pattern rifles.

[usmcspud]

I'll take it.
I'm in Merced. Would you be willing to meet at Alquist Arms in Turlock some evening?

[Hardwarejunkie]

How many magazines with the P220?

[anothergunnut]

The PTR is SPF.

The P220 comes with two factory mags. The photos of the P220 show greasy fingerprints; the finish on it is excellent.

[anothergunnut]

The PTR is gone but the FAL and Sig P220 are still available. Come on, you know you want them!

[anothergunnut]

Your wife called; she said buy one of these for your Christmas present!

[anothergunnut]

Thanksgiving; the perfect reason to buy one of these guns!

[anothergunnut]

[anothergunnut]

As noted in the original ad, prices are firm. Also, I will only participate in legal transactions through an FFL.

[anothergunnut]

These two fine guns are calling out for you to buy them.

[anothergunnut]

Added AR15 and AR10 lowers for trade only.

[anothergunnut]

Updated to indicate that I will sell the lowers.

[wolviak]

I'll take the Tactical Machining AR10 lower. PM sent.

[anothergunnut]

Stripped TM308 receiver sold. Added a used TM308 receiver.

[67goat]

Will take Sig upon agreed inspection.

[dsteinert]

I will take second TM308 lower. Responded to ARFCOM ad.

Payment sent.

[anothergunnut]

The TM308 lowers and Sig P220 are SPF.

[anothergunnut]

Forged mil-spec lowers for $250. I have these in hand and can FTF today or ship them to you in a few days.

[anothergunnut]

[anothergunnut]

Sig P220 is sold but AR15 receivers and FAL still available.