Calguns.net  

Home My iTrader Join the NRA Donate to CGSSA Sponsors CGN Google Search
CA Semiauto Ban(AW)ID Flowchart CA Handgun Ban ID Flowchart CA Shotgun Ban ID Flowchart
Go Back   Calguns.net > FIREARMS DISCUSSIONS > Rimfire Firearms
Register FAQ Members List Calendar Mark Forums Read

Rimfire Firearms .22, .17 and other Rimfire Handguns and Rifles

Reply
 
Thread Tools Display Modes
  #1  
Old 05-11-2012, 12:56 PM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default DIY: RUGER 10/22 Takedown Alignment Issue FIX.

i picked up my 10/22 TD from turners last night. when i inspected my rifle i noticed that it had an alignment issue, the fore end tilted to the left. turners kindly showed me 3 more new rifles and they all had that problem. i accepted the rifle because i trust the Ruger name.

i just got off the phone with Ruger and they explained to me how they fix the problem. so if you don't want to send your rifle back in and wait for it to be repaired continue reading. start at step 5 if you are not a 10/22 newb or a troll.

what you will need:

5/32 allen key.


step 1- safety check.
step 2- lock your bolt back and remove the magazine.
step 3- take down your take down.
step 4- put the fore end and barrel away you only need the receiver end.
step 5- using your 5/32 allen key loosen both screws (do not remove), allowing the piece of metal to move around.

step 6- using your thumb and index finger move the metal piece in the direction shown. (if it makes things worse try moving it in the opposite direction, your alignment issues may not be in the same direction as mine.)
step 7- while holding the metal piece in place with your finger tighten the screws.
step 8- assemble your take down rifle. you may need to adjust this a few more times before you hit center. (it took me 3 times before i was satisfied)


doing this fix will also tighten the connection a little. it will feel more snug. some believe that will improve accuracy.


About the gouges on the inside of the magwell. they are nothing to worry about, all of the guns have them. those two gouges is where the stocks are cut away from the mold. it is purely cosmetic.


GOOD LUCK!
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!

Last edited by secret.asian.man; 11-01-2013 at 9:30 AM..
Reply With Quote
  #2  
Old 05-11-2012, 1:05 PM
pennys dad's Avatar
pennys dad pennys dad is offline
CGSSA President
CGN Contributor - Lifetime
 
Join Date: Feb 2008
Location: CA
Posts: 5,755
iTrader: 190 / 100%
Default

Well Done! This is should be a sticky
__________________
Here to help

Jacob Rascon, (aka) Pennys Dad
CALGUNS Shooting Sports Association.
Jacob@CGSSA.Org

Psa 144:1-2
1. Blessed be the LORD my Rock, Who trains my hands for war, And my fingers for battle 2. My loving-kindness and my fortress, My high tower and my deliverer, My shield and the One in whom I take refuge, Who subdues my people under me.
Reply With Quote
  #3  
Old 05-11-2012, 1:12 PM
walletclan's Avatar
walletclan walletclan is offline
Member
 
Join Date: Apr 2011
Posts: 193
iTrader: 3 / 100%
Default

great post! this should get stickied.
Reply With Quote
  #4  
Old 05-11-2012, 6:15 PM
ROTC sniper's Avatar
ROTC sniper ROTC sniper is offline
Senior Member
 
Join Date: Jan 2010
Location: By the beach
Posts: 665
iTrader: 188 / 100%
Default

Awesome. Took all of 1 minute to adjust.
__________________
NRA Life Member ___________________________________________
____
WTS: Need a Bug out Bag that's battle tested? Large Alice Packs and Molle Packs, I got them.
http://www.calguns.net/calgunforum/s...=1#post7047942
Reply With Quote
  #5  
Old 05-11-2012, 7:26 PM
blap59 blap59 is offline
Member
 
Join Date: Nov 2009
Posts: 102
iTrader: 3 / 100%
Default

Ah, that's simple enough. I may get one of those if I come across one now
Reply With Quote
  #6  
Old 05-11-2012, 10:25 PM
ljgrasso's Avatar
ljgrasso ljgrasso is offline
Senior Member
 
Join Date: Dec 2010
Posts: 584
iTrader: 6 / 100%
Default

Definite sticky, thanks for the info.
__________________
Reply With Quote
  #7  
Old 05-11-2012, 11:26 PM
sharxbyte's Avatar
sharxbyte sharxbyte is offline
Senior Member
 
Join Date: Jul 2010
Location: Sacramento, Kommifornistan
Posts: 2,443
iTrader: 0 / 0%
Default

cool.. Know anyone selling "broken" ruger TD's for discount?
__________________
My AR is 7.62x39, so that if/when we get invaded, I can shoot their ammo back at them!


Quote:
Originally Posted by Falstaff View Post
Where is this ammo "Black market" he speaks of? Do they have .223 in stock?
My Home-Made Recurve Bow Thread


Own An 80%? CLICK HERE!


Kevin de Leon, on minority women and profiling.
Reply With Quote
  #8  
Old 05-12-2012, 7:39 AM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default

Quote:
Originally Posted by sharxbyte View Post
cool.. Know anyone selling "broken" ruger TD's for discount?
i've witnessed 3 guys REJECT their 10/22 Takedowns because of the alignment issue. it's still cheaper to buy it from the store at a sale price, how much does an FFL charge you to do a transfer in your area? where i'm at it's about $140+tax ($90-$100 to "Rent" the FFL License, and $30-$40 for DROS + tax) weather you are buying from a far away gun shop or buying from your buddy.
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!
Reply With Quote
  #9  
Old 05-12-2012, 10:38 PM
jimster716's Avatar
jimster716 jimster716 is offline
Member
 
Join Date: Oct 2011
Location: LA - Where only criminals can get ammo
Posts: 422
iTrader: 4 / 100%
Default

Thanks for the info. I adjusted mine as best as I could. Hopefully this also takes care of my groupings always going to the right of bullseye.
__________________
.22lr :: 9mm :: .40S&W :: .45ACP :: 12ga :: 5.56 :: .308
I'm an equal opportunity shooter.
Reply With Quote
  #10  
Old 05-15-2012, 10:22 PM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default

i know some of you still have 10/22 takedowns still in jail. bump!
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!
Reply With Quote
  #11  
Old 05-16-2012, 8:54 AM
Flintlock Tom's Avatar
Flintlock Tom Flintlock Tom is offline
Veteran Member
 
Join Date: Feb 2007
Location: Klamath Falls, OR
Posts: 2,741
iTrader: 32 / 100%
Default

Thank you for the well-documented fix. Great photos, too.
__________________
"Death is lighter than a feather; Duty is heavier than mountains."
John Ringo
Reply With Quote
  #12  
Old 05-16-2012, 9:25 AM
ssv3 ssv3 is offline
Junior Member
 
Join Date: May 2012
Posts: 3
iTrader: 0 / 0%
Default

I picked mine up two days ago and even Marion (the manager at Pasadena Turners) was surpirsed how perfect it lined up. He mentioned that most all of them were misaligned so he was shocked to see mine perfect out of the box. But thanks for the write up since a few buddies are getting theirs soon so I'll let them know how to fix if they have the issue.
Reply With Quote
  #13  
Old 05-16-2012, 9:30 AM
FamilyofShooters's Avatar
FamilyofShooters FamilyofShooters is offline
Member
CGN Contributor
 
Join Date: Apr 2012
Location: San Diego
Posts: 161
iTrader: 0 / 0%
Default

Great info..thanks. Had my 10/22 take down out for the first time on Sunday. Didn't experience the same issue but the scope mount base kept loosening up on me.
__________________
Proud Member of The Rock God Gun Club

Army: A body of men assembled to rectify the mistakes of the diplomats.
--Josephus Daniels--
Reply With Quote
  #14  
Old 05-16-2012, 11:23 PM
Dirtbikindad393's Avatar
Dirtbikindad393 Dirtbikindad393 is offline
Senior Member
 
Join Date: Feb 2012
Location: Komifornia
Posts: 977
iTrader: 25 / 100%
Default

Nice write up. Mine came perfectly aligned from the factory but I has to adjust the ring to tighten the fit between halves. That was a little sloppy or loose from the factory. What I do not like is the keeper ring for the adjustment ring is a loose sloppy fit but its held in by the barrel so I m not worrying about it.

My brother came over today and and we installed the auto bolt release, recoil buffer, extractor and I put a silver mag release lever into my 10/22 TD he did all but the mag release lever to his regular 10/22 and installed a new set of sights. I can't wait to go shoot them and see how they go with the mods.
__________________
NRA Life Member
GSSF Member
Front Sight Guardian Member

Have a family issue need to sell off my Front Sight Diamond Memberships to raise money.
PM if you have thought about buying one.

I don't regret burning some bridges. I regret that some people weren't on those bridges when I burnt them!
Reply With Quote
  #15  
Old 05-19-2012, 9:25 AM
m14carbine m14carbine is offline
Junior Member
 
Join Date: May 2012
Posts: 3
iTrader: 0 / 0%
Default

I too was disappointed when I saw my 10/22 td was not aligned when assembled. I discovered the allen screws a week later and fixed it. The only other thing I don't like is the difficult rear sight adjustment. I like the factory sights, I just do not like to "drift" adjust them. I scratched the barrel trying to unsuccessfully adjust, as it was hitting high right. I finally put a $30 Tasco red dot sight on it which works fine.
Reply With Quote
  #16  
Old 05-19-2012, 10:10 AM
m14carbine m14carbine is offline
Junior Member
 
Join Date: May 2012
Posts: 3
iTrader: 0 / 0%
Default

To assure a good fit and go back to zero on the 10/22 TD, do the following:
1) Assemble and hand tighten ring as much as possible (don't use a tool)
2) Dissemble without loosening ring
3) While dissembled, tighten ring two more clicks
4) Reassemble without moving ring anymore.
You will not have to repeat this process very of, if at all. This will bring it back to zero for many many take downs and reassembly's.
Reply With Quote
  #17  
Old 05-20-2012, 9:07 AM
40SWGlock 40SWGlock is offline
Member
 
Join Date: May 2012
Posts: 228
iTrader: 4 / 100%
Default

I pick mine up on Thursday from turners. Hopefully its aligned straight, if not I know what to do now. Thanks for the info!
Reply With Quote
  #18  
Old 05-22-2012, 11:57 PM
highender's Avatar
highender highender is offline
Practical Googleplex Guy
CGN Contributor - Lifetime
 
Join Date: Apr 2012
Location: in ignorant Kalifornia
Posts: 5,896
iTrader: 14 / 100%
Default

im picking up mine next week.....hopefully iti is fine...or else i knwo what to do...
thanks for the pics and write up.
__________________


Quote:
You may not like guns, and choose not to own one. That is your right. You might not believe in God. That is your choice. However, if someone breaks into your home, the first two things you're going to do are, 1) Call someone with a gun, 2) Pray they get there in time.
Reply With Quote
  #19  
Old 05-24-2012, 7:53 AM
walletclan's Avatar
walletclan walletclan is offline
Member
 
Join Date: Apr 2011
Posts: 193
iTrader: 3 / 100%
Default

I fixed mine a couple weeks ago using these instructions. It literally took me no more than 5 minutes with 3 tries. It is perfect now.
Reply With Quote
  #20  
Old 05-24-2012, 8:50 AM
ns3v3n's Avatar
ns3v3n ns3v3n is offline
Senior Member
 
Join Date: Feb 2007
Location: Bay Area
Posts: 1,539
iTrader: 26 / 100%
Default

It's kinda sad that most of them have this problem, especially from a company like Ruger.
__________________
The stuff that goes boom.
Reply With Quote
  #21  
Old 05-24-2012, 9:38 PM
ADROCK ADROCK is offline
Member
 
Join Date: Jan 2011
Location: San Diego
Posts: 293
iTrader: 61 / 100%
Default

I sent mine back to Ruger for the fix. They were so apologetic that they threw in 2 more 10 Rd mags(he wanted to give me a couple 25 rounders but then he saw my address.... Ca). Two weeks and a couple extra mags was worth the wait for me.
Reply With Quote
  #22  
Old 05-25-2012, 9:37 AM
walletclan's Avatar
walletclan walletclan is offline
Member
 
Join Date: Apr 2011
Posts: 193
iTrader: 3 / 100%
Default

Quote:
Originally Posted by ADROCK View Post
I sent mine back to Ruger for the fix. They were so apologetic that they threw in 2 more 10 Rd mags(he wanted to give me a couple 25 rounders but then he saw my address.... Ca). Two weeks and a couple extra mags was worth the wait for me.
Score! Too bad you couldn't take the 25 rounders....bummer.
Reply With Quote
  #23  
Old 05-27-2012, 3:34 PM
ANG Tactical's Avatar
ANG Tactical ANG Tactical is offline
Member
 
Join Date: Apr 2012
Location: Orange County, CA
Posts: 129
iTrader: 1 / 100%
Default

You would think that Ruger would have picked up on this by now and fixed the problem. It sucks getting a rifle then realizing you have to work on it to make it the way it should have been.
Reply With Quote
  #24  
Old 06-14-2012, 9:52 AM
King_John_I King_John_I is offline
Junior Member
 
Join Date: Jun 2012
Posts: 26
iTrader: 0 / 0%
Default

AWESOME POST!!!!!!!!!!!!!!!!! looked all over and randomly came across this. THANX Guys!!!

Fixed my boss's gun and looked like a freaking rockstar out of no where. HA

Last edited by King_John_I; 06-14-2012 at 9:54 AM..
Reply With Quote
  #25  
Old 06-14-2012, 10:18 AM
grabagun.com's Avatar
grabagun.com grabagun.com is offline
Vendor/Retailer
 
Join Date: May 2011
Posts: 22
iTrader: 2 / 100%
Default

Thank you very much....that alignment issue was making me crazy. I have had several people ask me how to fix their rifles and I had no idea how. I have one myself that is out of alignment and have not had time to mess with it. Great post!
__________________
www.grabagun.com
(972) 552-7246
support@grabagun.com
Reply With Quote
  #26  
Old 06-17-2012, 9:43 PM
Steve_In_29 Steve_In_29 is offline
Banned
 
Join Date: Nov 2009
Location: 29 Palms, SoCal
Posts: 5,689
iTrader: 10 / 100%
Default

I pick mine up Friday and didn't notice if it was misaligned but will be checking now. Thanks for the info.

I think they have so many with this issue due to the rush to get the guns out to the dealers prior to the availability announcement. I heard they shipped around 10K rifles prior to the kick-off.

One thing I think they could have done differently though would have been to include a clear mag with the rifle. After all it's a survival type weapon and an easily checked ammo supply would be a good thing.

Last edited by Steve_In_29; 06-17-2012 at 9:50 PM..
Reply With Quote
  #27  
Old 07-01-2012, 7:07 AM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default

Quote:
Originally Posted by FamilyofShooters View Post
Great info..thanks. Had my 10/22 take down out for the first time on Sunday. Didn't experience the same issue but the scope mount base kept loosening up on me.
blue locktite

or

red locktite if you don't plan on taking it off again.
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!

Last edited by secret.asian.man; 07-01-2012 at 7:13 AM..
Reply With Quote
  #28  
Old 07-04-2012, 8:56 AM
rogervzv's Avatar
rogervzv rogervzv is offline
Senior Member
 
Join Date: Feb 2011
Location: Huntington Beach, CA
Posts: 1,986
iTrader: 0 / 0%
Default

Quote:
Originally Posted by secret.asian.man View Post
i picked up my 10/22 TD from turners last night. when i inspected my rifle i noticed that it had an alignment issue, the fore end tilted to the left. turners kindly showed me 3 more new rifles and they all had that problem. i accepted the rifle because i trust the Ruger name.

i just got off the phone with Ruger and they explained to me how they fix the problem. so if you don't want to send your rifle back in and wait for it to be repaired continue reading. start at step 5 if you are not a 10/22 newb or a troll.

what you will need:

5/32 allen key.


step 1- safety check.
step 2- lock your bolt back and remove the magazine.
step 3- take down your take down.
step 4- put the fore end and barrel away you only need the receiver end.
step 5- using your 5/32 allen key loosen both screws (do not remove), allowing the piece of metal to move around.

step 6- using your thumb and index finger move the metal piece in the direction shown. (if it makes things worse try moving it in the opposite direction, your alignment issues may not be in the same direction as mine.)
step 7- while holding the metal piece in place with your finger tighten the screws.
step 8- assemble your take down rifle. you may need to adjust this a few more times before you hit center. (it took me 3 times before i was satisfied)


doing this fix will also tighten the connection a little. it will feel more snug. some believe that will improve accuracy.


About the gouges on the inside of the magwell. they are nothing to worry about, all of the guns have them. those two gouges is where the stocks are cut away from the mold. it is purely cosmetic.


GOOD LUCK!
Great post, SAM. +1 on making this a sticky.
__________________
Come and Take It!
Reply With Quote
  #29  
Old 07-18-2012, 10:24 PM
Readytoroll Readytoroll is offline
Member
CGN Contributor
 
Join Date: Jun 2012
Location: Los Angeles County
Posts: 161
iTrader: 2 / 100%
Default

Great post, works like a charm
Reply With Quote
  #30  
Old 07-26-2012, 1:20 AM
neverfinished neverfinished is offline
Junior Member
 
Join Date: Jan 2012
Posts: 24
iTrader: 0 / 0%
Default

Interesting, My ruger 10/22 takedown pulls slightly to the left so this may be the fix for it.
Reply With Quote
  #31  
Old 07-27-2012, 2:11 AM
tvfreakarms's Avatar
tvfreakarms tvfreakarms is offline
Senior Member
 
Join Date: Jul 2009
Location: sactown
Posts: 2,200
iTrader: 4 / 100%
Default

Seems like some quality control issues.
No very good in my opionion.
Reply With Quote
  #32  
Old 08-04-2012, 8:29 AM
GunDog GunDog is offline
Senior Member
 
Join Date: Dec 2008
Posts: 1,475
iTrader: 23 / 100%
Default

Got 'er done! Quick and easy fix. Great thread. Thanks
Reply With Quote
  #33  
Old 08-14-2012, 2:29 PM
onegtalon's Avatar
onegtalon onegtalon is offline
Calguns is my Facebook!
CGN Contributor
 
Join Date: Aug 2011
Location: SF Bay Area
Posts: 2,424
iTrader: 60 / 100%
Default

Anyone know if this will fix a up/down alignment issue? My barrel is canted like 3 degrees downwards.
__________________
Laws and common sense is all up to interpretation to us humans... and guess what? Humans suck.

Onegtalon... toooooo many hobbies man !...

HDF, CGN/CGF member
Reply With Quote
  #34  
Old 08-14-2012, 3:46 PM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default

Quote:
Originally Posted by onegtalon View Post
Anyone know if this will fix a up/down alignment issue? My barrel is canted like 3 degrees downwards.
i think that's a warranty issue.
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!
Reply With Quote
  #35  
Old 08-15-2012, 7:32 AM
onegtalon's Avatar
onegtalon onegtalon is offline
Calguns is my Facebook!
CGN Contributor
 
Join Date: Aug 2011
Location: SF Bay Area
Posts: 2,424
iTrader: 60 / 100%
Default

Quote:
Originally Posted by secret.asian.man View Post
i think that's a warranty issue.
Yea... My LGS guy already on the phone with them.. Kinda sucks if I have to do DROS again... At 50 yards it was shooting something like 20 feet low. With the scope maxed out it was still 2 feet low.....


Sent from my iPhone...
__________________
Laws and common sense is all up to interpretation to us humans... and guess what? Humans suck.

Onegtalon... toooooo many hobbies man !...

HDF, CGN/CGF member
Reply With Quote
  #36  
Old 08-23-2012, 4:06 PM
R1J1D's Avatar
R1J1D R1J1D is offline
Member
 
Join Date: Sep 2009
Location: SFV
Posts: 125
iTrader: 3 / 100%
Default

Quote:
Originally Posted by secret.asian.man View Post
i've witnessed 3 guys REJECT their 10/22 Takedowns because of the alignment issue. it's still cheaper to buy it from the store at a sale price, how much does an FFL charge you to do a transfer in your area? where i'm at it's about $140+tax ($90-$100 to "Rent" the FFL License, and $30-$40 for DROS + tax) weather you are buying from a far away gun shop or buying from your buddy.

you have got to be kidding me!! really 90-100$ for using their FFL? thats outrageous I am glad I moved away when I did. my local FFL charges me 15$.
and we have no tax,

I am really pissed off for you guys tho Cali. is worse than the mob shoot I'd rather pay them for protection.
Reply With Quote
  #37  
Old 08-24-2012, 3:46 PM
secret.asian.man's Avatar
secret.asian.man secret.asian.man is offline
Senior Member
 
Join Date: Aug 2011
Location: Monterey Park, CA
Posts: 746
iTrader: 11 / 100%
Default

Quote:
Originally Posted by R1J1D View Post
you have got to be kidding me!! really 90-100$ for using their FFL? thats outrageous I am glad I moved away when I did. my local FFL charges me 15$.
and we have no tax,

I am really pissed off for you guys tho Cali. is worse than the mob shoot I'd rather pay them for protection.
i see a mistake a made when writing that. i'll edit.

PPT = $35
Transfer from another store PPT or NEW = $90 - $100 FFL license rental + $35 for DROS + TAX on price of gun and shipping.
__________________

If guns are outlawed, then an outlaw I'll be...
WHEN YOU COME FOR MINE, BRING YOURS!
ΜΟΛΩΝ ΛΑΒΕ!




ammo donations accepted here!
Reply With Quote
  #38  
Old 10-08-2012, 6:55 PM
GreggE GreggE is offline
Junior Member
 
Join Date: Dec 2011
Location: in the belly of the Liberal beast (San FranSh*tHole)actually East Bay Concord 30 minutes from hell
Posts: 55
iTrader: 2 / 100%
Default Picked up my 10/22 Take Down Today

Picked up my 10/22 today and no alignment issues at all. Did not get a chance to shoot it (will do Friday) but gun seems well put together. Mounted a silver Simmons 3-9x32 A/o scope on it and it looks great. Gun with scope fits in bag with no problems. Will get back on Friday after shooting it.
__________________
You may find my body in a ditch, but, I will be lying on a bed of brass
Reply With Quote
  #39  
Old 10-25-2012, 11:32 PM
bsg bsg is offline
I need a LIFE!!
 
Join Date: Jan 2009
Location: san gabriel valley
Posts: 25,779
iTrader: 7 / 100%
Default

i don't have the 10/22 Takedown yet, but will bookmark this thread for future reference.

thanks for the heads-up and detailed instructions.
Reply With Quote
  #40  
Old 12-28-2012, 11:22 AM
superbarnie's Avatar
superbarnie superbarnie is offline
Member
 
Join Date: Dec 2012
Posts: 394
iTrader: 0 / 0%
Default

I think I'm going to buy a Ruger 10/22 TD soon. But I'm really new to this stuff, so can someone explain to me what is a alignment issue, and how to detect it?
Does anyone have a photo of an badly aligned one for reference?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -8. The time now is 7:00 PM.




Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Proudly hosted by GeoVario the Premier 2A host.
Calguns.net, the 'Calguns' name and all associated variants and logos are ® Trademark and © Copyright 2002-2016, Calguns.net an Incorporated Company All Rights Reserved.