View Single Post
  #80  
Old 07-13-2010, 12:37 AM
pacrimguru's Avatar
pacrimguru pacrimguru is offline
Veteran Member
 
Join Date: Sep 2008
Location: Pasadena, CA
Posts: 3,468
iTrader: 168 / 100%
Default



To see how I built & painted this 9mm AR15, click here.

Upper: YHM / Cerro Forge Receiver
Barrel: Spike's Tactical 9mm 16", 1/10 twist, re-profiled by ar15barrels.com
Rail: VTAC 13" Extreme BattleRail
- Spike's Tactical 9mm A2 Flash Hider
- CMMG Ramped 9mm Bolt Carrier Group
- VLTOR/BCM Gunfighter Mod.4 Charging Handle
- KAC M4 Flip-Up Front Sight
- KAC 300M Rear BUIS
- Magpul AFG
- VTAC LPSM Sling Mount
- Magpul Rail Ladders
- Colt 9mm Gas Deflector and 9mm Ejection Port Cover

Lower: Kaiser Defense / Calguns.net "Bear" Lower
- USGI Standard Trigger (6-8 lb. pull, not sure)
- LMT Ambi Selector
- Hahn Precision Dedicated 9mm Mag Block
- Magpul MIAD Grip Full Kit
- Magpul B.A.D.
- Magpul ASAP
- LMT Heavy Duty QD Push Button Swivel
- KNS Non-Rotating Trigger and Hammer Pins
- Prince50 Bullet Button (CA Compliance Part)
- Prince50 Extended Take Down Pin

Stock: LMT SOPMOD Gen. 1
- KAC M4 Sliding Buttstock Mount
- MilSpec Receiver Extension
- Rock River Arms 9mm Buffer Spring
- Spike's Tactical ST-9X 9mm Buffer

Magazine: C Products 10 Round 9mm (CA Compliant 10 rnd.)

Optic: Aimpoint Micro H-1 on LaRue Tactical T-1 Mount

Light: Surefire X300

Paint: Mixture of Rustoleum Primers with Aluma-Hyde II Matte Coat on top

Sling: Magpul MS2 Single Point Sling

Use: Shooting at 0-50 yards, Competition

Weight: 8lbs. 6oz. (with unloaded magazine attached)

------------------------------------------------------------------------------



Upper: KAC SR 15 E3 IWS Special Run Upper with Integral Folding 200-600m Rear Sight
Barrel: KAC 16", 1/7 twist, Mid-Length Gas System
Rail: KAC URX II Rifle Length
- KAC Triple Tap Muzzle Brake
- KAC E3 Bolt Carrier Group
- VLTOR/BCM Gunfighter Mod.4 Charging Handle
- CMMG Low Profile Gas Block
- KAC Handstop
- Magpul XTM Rail Panels (Stippled by Valk/Tac Custom Shop)

Lower: L.A.R. LAR-15
- USGI Standard Trigger (6-8 lb. pull, not sure)
- LMT Ambi Selector
- Magpul MIAD Grip Full Kit
- Magpul ASAP
- KAC Combat Trigger Guard
- Phase 5 Extended Bolt Release (EBRv2)
- KNS Non-Rotating Trigger and Hammer Pins
- Prince50 Bullet Button (CA Compliance Part)
- Prince50 Extended Take Down Pin

Stock: LMT SOPMOD Gen. 2
- Mil-Spec Receiver Extension
- Standard Carbine Buffer
- Standard Carbine Buffer Spring


Magazine: Magpul PMag (CA Compliant 10/30)

Optic: Aimpoint Micro T-1 on KAC T-1 Mount

Light/Illumination:
- Insight ATPIAL (AN/PEQ-15)
- Surefire X300
- Surefire SR07-D-IT Remote Switch

Paint: Lower is painted with Aluma-Hyde II in Coyote

Sling: Magpul MS2 Single Point Sling

Use: Shooting at 0-100 yards, Tactical Carbine Classes

Weight: 8lbs. 8oz. (with unloaded magazine attached)
------------------------------------------------------------------------------

Not an AR (obviously)...



CAI WASR10
Modifications:

- Ultimak M1-B Scout Mount (Gas Tube Optic Mount)
- ACE Grip Adapter
- Magpul MIAD Grip
- homemade mag lock

Magazine: US Palm AK30/10 Magazine (CA Compliant 10/30)

Optic: Aimpoint H-1
__________________
AR Profiles: 1 | 2 | Past AR's: 1 | 2

Last edited by pacrimguru; 01-11-2011 at 12:56 PM..
Reply With Quote