Calguns.net

Calguns.net (http://www.calguns.net/calgunforum/index.php)
-   Gunsmithing & How To (http://www.calguns.net/calgunforum/forumdisplay.php?f=114)
-   -   Plz Direct me to a Gunsmith in LA/Burbank (http://www.calguns.net/calgunforum/showthread.php?t=652653)

rimfire78 12-04-2012 9:20 PM

Plz Direct me to a Gunsmith in LA/Burbank
 
I just bought a new rifle and need some help with a mod. Does anyone know of a local gunsmith who could help?

Thanks for your help
I'm in Los Angeles.

rimfire78 12-04-2012 10:03 PM

Anyone?

gesundheit 12-04-2012 10:21 PM

First thing: Take a deep breath and step away from the rifle.

Contact AR15Barrels here. He is not that far away from you in Van Nuys.

rimfire78 12-05-2012 6:46 AM

Quote:

Originally Posted by gesundheit (Post 9854527)
First thing: Take a deep breath and step away from the rifle.

Contact AR15Barrels here. He is not that far away from you in Van Nuys.

;)
Thanks

ar15barrels 12-06-2012 9:10 PM

Quote:

Originally Posted by rimfire78 (Post 9854205)
I started trying to remove the front chopped gas block so that I can install a YHM flip sight, but I can't get the taper pins to budge even after soaking them in WD-40.
AT this point, I'm beginning to make a mess of things. The next step would be drilling them out

Drilling them never ends well.
I have a pressing fixture for removing and installing taper pins.

xbuilder9mm 12-07-2012 7:13 PM

Without a question and worth the drive. Bain & Davis in San Gabriel, Ca, you won't be disappointed

richard310 12-07-2012 8:11 PM

2nd on ar15barrels. Going to be closest to you.

vw69turbobug 12-07-2012 10:38 PM

the pins only press out one way only. i have drilled a pin out but its not fun (freind try doing the same thing and mushroom the **** out of the pins) post sum pic of how bad it is now might need to drill them out

Grapevine 12-11-2012 2:49 PM

Rimfire,

Call Addax Tactical located in the City of San Fernando.

http://www.addaxtactical.com/store/pc/home.asp

Milspec714 12-11-2012 6:23 PM

Quote:

Originally Posted by rimfire78 (Post 9854205)
I just bought a new Ar type rifle. I started trying to remove the front chopped gas block so that I can install a YHM flip sight, but I can't get the taper pins to budge even after soaking them in WD-40.
AT this point, I'm beginning to make a mess of things. The next step would be drilling them out but I'm not that brave.
Has anyone removed one of these, or know of a local gunsmith who could help?

Thanks for your help
I'm in Los Angeles.

Did you pick it up?

Press Check 12-11-2012 7:57 PM

Quote:

Originally Posted by Grapevine (Post 9897806)
Rimfire,

Call Addax Tactical located in the City of San Fernando.

http://www.addaxtactical.com/store/pc/home.asp

Disclaimer:

ADDAX TACTICAL IS NOT RESPONSIBLE FOR COSMETIC SCRATCHES OR BLEMISHES THAT CAN POSSIBLY OCCUR DURING PARTS INSTALLATION.

WE WILL DO OUR BEST NOT TO BLEMISH ANY PARTS DURING INSTALLATION.


Sorry, but IMO, that's garbage.

Addax 12-11-2012 10:14 PM

Quote:

Originally Posted by Press Check (Post 9900542)
Disclaimer:

ADDAX TACTICAL IS NOT RESPONSIBLE FOR COSMETIC SCRATCHES OR BLEMISHES THAT CAN POSSIBLY OCCUR DURING PARTS INSTALLATION.

WE WILL DO OUR BEST NOT TO BLEMISH ANY PARTS DURING INSTALLATION.


Sorry, but IMO, that's garbage.

We agree.

That is an old disclaimer that was supposed to be removed from our website during our last website refresh a few month ago, and replaced with the following updated disclaimer:

ADDAX TACTICAL IS NOT RESPONSIBLE FOR ANY EXISTING SCRATCHES AND BLEMISHES ON CUSTOMER SUPPLIED PARTS.

ADDAX TACTICAL IS NOT RESPONSIBLE FOR CUSTOMER SUPPLIED PARTS THAT DO NOT FIT OR INSTALL PROPERLY.

The website admin. has been informed of the oversight, and the new disclaimer should be posted up shortly.

Thanks,
Addax Tactical


All times are GMT -8. The time now is 1:08 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2016, vBulletin Solutions, Inc.