PDA

View Full Version : I'm getting ready to build...anything else that I need?


sactime
07-19-2007, 1:36 PM
Several members helped me out in the chat yesterday about building up a stag-15. I just want to confirm that these parts will work together, and if there is anything you guys would change let me know.

http://www.tenpercentfirearms.com/index.php?main_page=product_info&products_id=267
C Products 10 Rnd Mag, Bullet Button Kit, Extended Take Down Pin
$47

http://ddsranch.com/store/product_info.php?cPath=20_46_271&products_id=533&osCsid=01f37f0647d7af4044d35f5c966f640b
Stag Arms Stag-15 5.56mm (223 Rem) Caliber Stripped Lower Receiver
$100

http://ddsranch.com/store/product_info.php?cPath=20_46_271&products_id=547&osCsid=01f37f0647d7af4044d35f5c966f640b
Stag Arms Lower Receiver Parts Kit For AR15 Type Rifles
$60

http://www.tenpercentfirearms.com/index.php?main_page=product_info&cPath=3&products_id=129
Stag Arms Tactical Stock
$80


As for the upper assembly I can't decide between:

http://www.tenpercentfirearms.com/index.php?main_page=product_info&cPath=16_20&products_id=5
Stag Arms Model 1H Upper Assembly
$515

http://www.tenpercentfirearms.com/index.php?main_page=product_info&cPath=16_20&products_id=8
Stag Arms Model 4H Upper Assembly
$525


Total: $865/$875, depending on which upper assembly.

I would also like to confirm that the only part that needs to be shipped to an FFL would be the stripped lower receiver.

Also, does anyone have some close up pictures of the bullet button, which can give me a good idea of how it works exactly.

Thanks.

BlackReef
07-19-2007, 1:41 PM
I just bought the Stag 1H and installed it yesterday.

http://www.blackreefdesign.com/misc/gun/1.jpg

I would def. recommend it.

Also check out Spike's Tactical (www.spikestactical.com) for stripped OLL's. They may be a little cheaper and have great service. Talk to Angela

1064chubbs
07-19-2007, 1:52 PM
go 1H.;)

shark92651
07-19-2007, 2:29 PM
With a Bullet Button you may not need the extended takedown pin - those are mostly for when people need to open up the rifle frequently to reload. Then again, it is only a few bucks more anyway. The Bullet Button is a pretty simple concept - it is a magazine release button inside a fixed, outer "shell". You just stick a bullet tip or other tool into the hole to release the magazine, but the hole is too small to allow you to manipulate it with your finger or without the use of a tool.

Here is the original thread with pic:

http://www.calguns.net/calgunforum/showthread.php?t=46802&highlight=bullet+button

Socal858
07-19-2007, 2:44 PM
you may want to pick up a CAR stock wrench to facilitate tightening your stock, and some CLP and a cleaning kit

after you are assembled, learn and practice field stripping the bolt carrier/bolt apart

Sig357
07-19-2007, 3:36 PM
Yes the CAR stock wrench is helpful, CLP, cleaning kit and lots of ammo.

costayoung
07-19-2007, 3:47 PM
To answer your questions:

Yes, all of those parts will work together. And yes, the only part that needs to go to the FFL is the lower receiver.

aplinker
07-19-2007, 7:51 PM
Yes the CAR stock wrench is helpful, CLP, cleaning kit and lots of ammo.

+3 on all of those, especially the stock wrench.

I'd also suggest getting several mags (I'd push you towards Bushmaster 10/20's if you can find them).

sactime
07-19-2007, 8:02 PM
Thank you all for the great info. Does anyone have some good closeups of the entire right side (bullet button side) of the gun?

Thanks

aplinker
07-19-2007, 10:28 PM
Thank you all for the great info. Does anyone have some good closeups of the entire right side (bullet button side) of the gun?

Thanks

got this from Cold War Shooters.

http://www.coldwarshooters.net/images/bb.JPG

If you notice the outside is black, you can not put your finger inside there, so you put a bullet inside this and push on the silver part.