PDA

View Full Version : All Colt 16" M4 upper complete **SPF**


QuarterBoreGunner
06-18-2007, 11:24 AM
Funding a new project.
**SPF**
Thanks to everyone that looked!

I bought a Colt M4 upper kit, complete, back in 1998 I believe and had it on a reg'd Bushy lower for a long time, but didn't shoot it that much, I believe, no more than 500 rounds, this is not new but very much NOT abused.
Asking $600, which I think is fair, considering that it's all Colt, and comparing it to others on GunBroker.com

This is the same upper that comes on the current LE6920 rifle:


Barrel is true 16.1" in length with a standard A2 flash suppressor and bayo lug.
Barrel is marked "C MP 5.56 NATO 1/7" with a thin Gov profile under the double heat shield handguards. Barrel is stamped "10/97" under the handguards near the FSB. As far as I can tell, this does NOT have a chrome bore or chamber.
Front sight base is "F" stamped.
Comes with the Colt side sling adaptor.
Receiver is the true M4 type; marked "M4" over the clover leaf (that's a cat hair in the picture, not a scratch) with the extended feedramp cuts in the receiver. The rails on the upper are not numbered.
Comes with Colt "C MP" marked bolt and carrier. Carrier has fully enclosed firing pin but does NOT have the full ring at the rear of the carrier (NOT, repeat, NOT a FA bolt carrier.) Also has upgraded "black" extractor rubber buffer.
No carrying handle with this upper.
The only non-Colt part on it is a Badger Ord Tac Latch (http://www.badgerordnance.com/productgroup.php?id=latch#) (P/N 249-02) on the charging handle.


Again, not new, but nicely broken in. No scratches, dings or other damage, just honest wear in the usual spots. DISCLAIMER: If you remove the handguards, you'll see some aluminium scuffing from where I had the barrel in a armorers vice; honestly I cannot remember why I had it in the vice, but the barrel has never been removed from the upper. The silver scuffing is from the soft aluminum of the vise and is NOT bare barrel metal. I scrubbed most of it off with Hoppes and a toothbrush. Just want y'all to be clear, right?

Pictues below.

Barrel markings.
http://www.pacificapocalypse.com/online_assets/M4_barrel.jpg

Cat hair; not a scratch.
http://www.pacificapocalypse.com/online_assets/front.jpg

FSB Marking
http://www.pacificapocalypse.com/online_assets/FSB_left.jpg

Right rear of receiver. Discoloration is from CLP.
http://www.pacificapocalypse.com/online_assets/right_rear.jpg

PM's or emails for any questions.

duenor
06-18-2007, 5:20 PM
will this fit perfectly on a regular (large pin hole i think) stag receiver?

whats round count aprox?

QuarterBoreGunner
06-18-2007, 5:27 PM
This is a "small hole" upper and will fit in all "mil-spec" small hole receivers with standard takedown pins.

Oops; forgot to add, round count is around 500 as I recall. No more than that.

blackrifle
06-18-2007, 9:46 PM
Good deal for a real Colt upper! Just a few dollars over Stag, LMT, etc. and you get the best! If I didn't already have several Colt's...

Jicko
06-19-2007, 12:03 AM
Good deal for a real Colt upper! Just a few dollars over Stag, LMT, etc. and you get the best! If I didn't already have several Colt's...

TOTALLY GREAT DEAL!

Especailly this is a 1x7 Colt !!!!!!

Stags are mostly just 1x9...

Teletiger7
06-19-2007, 3:56 PM
will this fit perfectly on a regular (large pin hole i think) stag receiver?

whats round count aprox?

Don't they sell an adaptor?