PDA

View Full Version : Its almost 3:30am...I'm wondering how to attach a "Krink" top cover...go figure!


technique
07-04-2009, 2:18 AM
So hows that work? One kit is a demill, the cover was removed in the process so I have no idea how it went on to begin with.

Rivets?
Is there a specific rivet I should be shopping for?
Where might one find such a rivet?
Should I order an extra AK builder set? Would it contain the right size?
Is it like a center support type rivet? Or a long rivet? I cant imagine it any other way.

Help a brother out! I'm trying to get everything I need.:)

Thanks.
Tech

technique
07-04-2009, 2:28 AM
I guess adding that its a Bulgi AKS74u kit may help...info needed for Yugo M92 also (likely that I have the part for the M92...but identifying what it looks like is what I need)

Norccer
07-04-2009, 2:48 AM
Can't help but atleast you know you aren't alone. Bahahaha

yey for drunk people wanting rides at 3 am.

hybridatsun350
07-04-2009, 2:51 AM
I can't help you, but I can't believe I'm up this ****ing early getting ready for work! Uhg!

marxdspot
07-04-2009, 8:53 AM
I'm actually away from home, but I've built a couple of M92's a while ago. From memory, you should have a three critical parts
1. Rivet
2. Washer for Rivet
3. Pin which roughly measures .75cm x 3-4cm with an angle in one end.

The pin should go into the hole located in the rear block. The purpose of this pin is to hold the gas tube in place when the top cover is closed. The angled end should point down and face towards the gas tube and vice versa the flat end faces the top cover. Once you have that installed, there should be a rivet that as a flat end that should slip right into holes where the top cover and rear block meet. After you do that, there should be a small washer that matches the diameter of the flat end of the rivet. Once installed, you have to press the rivet to flatten. You don't have to press too hard. Slight pressure would be ample to keep that sucker in place. With regards to which way the flat end faces, I believe the preformed flat end faces left...correct me if I'm wrong.

I'd take pictures for you, but I'm not at home right now enjoying and the Aloha sunrise in Kauai. ALOHA!...and good luck. Feel free to PM me if you have any other questions. I'll try to get back to you when I can.

technique
07-04-2009, 11:01 AM
thanks....I have a feeling its not going to be easy finding one to use for the Bulgi kit.



*edit*...found one at Kvar.

technique
07-10-2009, 1:11 PM
No I have not assembled yet....I'm waiting to Build the M92, its a Virgin and I don't have the skills to handle that yet....I did, Identify the parts to use.

I found K-Var had the parts I needed for my Bulgi and I now have those and I hope to assemble that kit at the NCal build party next month!:chris:

technique
07-10-2009, 1:25 PM
I'll finish eating at report back....I'll see if I can get mine to fit.

But....since you mentioned "Flat side"....I know my Factory Yugo Center support also has a flat side.

I assume you know more than I....but just in case, make sure its the right part.

technique
07-10-2009, 1:58 PM
Okay...

So no way it could be the center support on the M92...its much too small. The bugi is the one thats much bigger.

The two parts shown...Rivet/pin...And washer thing....thats all I know. The other parts (I'm sure I have) I don't know what they look like.
http://i285.photobucket.com/albums/ll42/technique408/zm92003.jpg

Again...I have no clue but they seem to fit.
http://i285.photobucket.com/albums/ll42/technique408/zm92001.jpg
http://i285.photobucket.com/albums/ll42/technique408/zm92002.jpg

technique
07-10-2009, 2:10 PM
Okay...so here it is with the handguard retainer installed. It still seems to fit fine.

http://i285.photobucket.com/albums/ll42/technique408/zm92.jpg

JohnBrian
07-10-2009, 5:15 PM
I got that far. Mine hits the front handguard short and if I push it back towards the rear I won't slide over the top cover.
Make sure your handguard/gas tube cover is fully seated. If so, you may need to file the handguard/gas tube cover a little to get the pin to fully seat.

My M92 looks like this

http://www.calguns.net/calgunforum/attachment.php?attachmentid=27667&stc=1&d=1247274771

http://www.calguns.net/calgunforum/attachment.php?attachmentid=27668&stc=1&d=1247274771

badicedog
07-10-2009, 5:21 PM
I guess adding that its a Bulgi AKS74u kit may help...info needed for Yugo M92 also (likely that I have the part for the M92...but identifying what it looks like is what I need)

I'll take a pic of mine in the morning when I get home.:43:

aplinker
07-10-2009, 6:10 PM
Its almost 3:30am...I'm wondering how to attach a "Krink" top cover...go figure!

I guess you finally did it - you've downloaded all the porn there is on the net.

technique
07-10-2009, 8:41 PM
I'll take a pic of mine in the morning when I get home.:43:

Cool! I would like to see a built one!



I guess you finally did it - you've downloaded all the porn there is on the net.

See the problem with that is that my Laptop has no sound...it just went out one day.....Now I have to imagine the moaning, and try to figure out what the midgets are saying:o